Ab60F Automatic Transmission Transaxle. Automatic Transmission Assembly (For 1Vd-Ftv) Removal

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200

Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

PRECAUTION
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
REMOVE NO. 2 ENGINE UNDER COVER
REMOVE OIL PAN PROTECTOR ASSEMBLY
REMOVE FRONT FENDER APRON TRIM PACKING A
REMOVE FRONT FENDER APRON TRIM PACKING C
DRAIN AUTOMATIC TRANSMISSION FLUID
DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
REMOVE FRONT PROPELLER SHAFT ASSEMBLY
REMOVE PROPELLER SHAFT ASSEMBLY
REMOVE EXHAUST PIPE (w/ DPF)
REMOVE EXHAUST PIPE (w/o DPF)
REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
DISCONNECT OIL COOLER TUBE
SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
DISCONNECT BREATHER PLUG HOSE
DISCONNECT WIRE HARNESS AND CONNECTOR
REMOVE OIL PAN COVER
REMOVE TRANSMISSION HOUSING COVER
REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
REMOVE TRANSFER ASSEMBLY
REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
INSPECT TORQUE CONVERTER ASSEMBLY

Automatic Transmission Assembly (For 1Vd-Ftv) -- Removal

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Remove the 3 bolts and screw.

Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.

4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Remove the 3 bolts and 2 screws.

Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.

5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Remove the 10 bolts and No. 1 engine under cover.

6. REMOVE NO. 2 ENGINE UNDER COVER

Remove the 2 bolts and No. 2 engine under cover.

7. REMOVE OIL PAN PROTECTOR ASSEMBLY

Remove the 4 bolts and oil pan protector.

8. REMOVE FRONT FENDER APRON TRIM PACKING A

Remove the 3 clips and front fender apron seal front RH.

9. REMOVE FRONT FENDER APRON TRIM PACKING C

Remove the 4 clips and front fender apron seal rear RH.

10. DRAIN AUTOMATIC TRANSMISSION FLUID

Remove the drain plug and gasket, and drain the ATF.

Install a new gasket and the drain plug.
Torque:
20 N*m{204 kgf*cm, 15 ft.*lbf}

11. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.

12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

(Click here)

13. REMOVE PROPELLER SHAFT ASSEMBLY

(Click here)

14. REMOVE EXHAUST PIPE (w/ DPF)

(Click here)

15. REMOVE EXHAUST PIPE (w/o DPF)

(Click here)

16. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

Remove the 2 bolts and oil pan insulator.

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.

17. DISCONNECT OIL COOLER TUBE

Disconnect the 2 transmission oil cooler hoses from the oil cooler tube union.

Remove the 3 bolts and separate the oil cooler tube from the engine.

18. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

19. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

Remove the engine mounting hole cover.

Remove the 4 bolts of the rear engine mounting insulator.

Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe).Automatic Transmission Assembly (For 1Vd-Ftv) Removal

Remove the 4 nuts, 4 bolts and frame crossmember.

20. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

Remove the 4 bolts and rear engine mounting insulator from the transmission.

21. DISCONNECT BREATHER PLUG HOSE

Disconnect the 3 breather plug hoses from the wire harness.

22. DISCONNECT WIRE HARNESS AND CONNECTOR

Remove the bolt and disconnect the ground cable.

Tilt the transmission downward.
NOTICE:
Make sure the cooling fan does not contact the fan shroud.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.

HINT:
Detach the claw, press down the lever, and then disconnect the transmission wire connector.