Clutch Pedal (For Lhd) Installation

Apply MP grease to the contact surface of the clutch pedal spring holder.

Install the clutch pedal spring holder to the clutch pedal support.

Apply MP grease to the inside of a new clevis bush.

Install the clevis bush to the clutch pedal.

HINT:

Install the clevis bush from the right side of the vehicle.

Apply MP grease to the inside of the clutch pedal turnover bush.

Install the clutch pedal turnover bush to the clutch pedal.

Install the 2 clutch pedal cushions to the clutch pedal.

Apply MP grease to the inside and outside of 2 new bushes.

Install the 2 bushes to the clutch pedal.

Apply MP grease to the clutch pedal shaft collar.

Install the clutch pedal shaft collar to the clutch pedal.

Install the clutch pedal pad to the clutch pedal.

Install the clutch pedal to the clutch pedal support with the nut, washer and bolt.

Torque:

34 N*m{350 kgf*cm, 25 ft.*lbf}

HINT:

Install the bolt from the right side of the vehicle.

Apply MP grease to the contact surface of the clevis pin and clevis bush.

Install the wave washer to the clevis pin.

Connect the clevis of the master cylinder to the clutch pedal with the clevis pin.

Install a new clip to the clevis pin.

Apply MP grease to the inside and outside of the spacer and pin of the clutch pedal support.

Install the spacer to the spring.

Install the spring to the clutch pedal support with 2 new E-rings.

Apply MP grease to the contact surfaces of the spring holder, clutch pedal and spring.

Move the pedal to the full stroke position.

Install the spring to the clutch pedal and spring holder.

Install the clutch pedal support with clutch master cylinder with the bolt and 2 nuts.

Torque:

for bolt:

18 N*m{184 kgf*cm, 13 ft.*lbf}

for nut:

14 N*m{145 kgf*cm, 10 ft.*lbf}

Connect the clutch start switch connector.

w/ Cruise Control System:
Connect the clutch switch connector.

Using a union nut wrench, connect the flexible hose tube.

Torque:

15 N*m{155 kgf*cm, 11 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

Connect the clutch reservoir tube with a new clip.

Fill the reservoir with brake fluid.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT 3

Remove the release cylinder bleeder plug cap.

Connect a vinyl tube to the bleeder plug.

Depress the clutch pedal several times, and then loosen the bleeder plug while the pedal is depressed.

When fluid no longer comes out, tighten the bleeder plug, and then release the clutch pedal.

Repeat the previous 2 steps until all the air in the fluid is completely bled.

Tighten the bleeder plug.

Torque:

11 N*m{110 kgf*cm, 8 ft.*lbf}

Install the bleeder plug cap.

Check that all the air has been bled from the clutch line.

Check that the clutch pedal height is correct.

Standard Clutch Pedal Height from Tibia Pad:

162.7 to 172.7 mm (6.41 to 6.79 in.)

Adjust the clutch pedal height.

1. Loosen the lock nut and turn the stopper bolt or clutch switch until the height is correct. Tighten the lock nut.
   

   Torque:

   16 N*m{160 kgf*cm, 12 ft.*lbf}

Check that the clutch pedal free play and push rod play are correct.

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.

1. Depress the clutch pedal until the clutch resistance begins to be felt.
   

   Standard Pedal Free Play:

   5.0 to 15.0 mm (0.197 to 0.591 in.)
   

2. Gently depress the clutch pedal until the resistance begins to increase a little.
   

   Standard Push Rod Play at Pedal Top:

   1.0 to 5.0 mm (0.0394 to 0.197 in.)
   

Adjust the clutch pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.

1. Loosen the lock nut and turn the clutch push rod until the clutch pedal free play and push rod play are correct.
   

   NOTICE:

   If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.

2. Tighten the lock nut.
   

   Torque:

   12 N*m{120 kgf*cm, 9 ft.*lbf}

3. After adjusting the clutch pedal free play and push rod play, check the clutch pedal height.
   

   Standard Clutch Pedal Height from Tibia Pad:

   162.7 to 172.7 mm (6.41 to 6.79 in.)
   

Check the clutch release point.

1. Pull the parking brake lever and chock the wheels.
   

2. Start the engine and allow it to idle.
   

3. Without depressing the clutch pedal, slowly move the shift lever to R until the gears engage.
   

4. Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.
   

   Standard Distance from Pedal Stroke End Position to Release Point:

   20 mm (0.787 in.) or more
   

   If the distance is not as specified, perform the following operations:
   
   1. Check the clutch pedal height.
      
   2. Check the push rod play and pedal free play.
      
   3. Bleed the clutch line.
      
   4. Check the clutch cover and disc.
      

Check the fluid level.
If the brake fluid level is low, check for leaks and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair or replacement.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT 3

Attach the 2 claws and connect the DLC3.

Install the lower instrument panel sub-assembly with the 5 bolts.