Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200
INSPECT SPEED SENSOR SP2 INSTALLATION
CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)
DTC P0722 Output Speed Sensor Circuit No Signal |
DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.
| DTC Code | DTC Detection Condition | Trouble Area |
| P0722 | All the conditions below are detected 500 times or more continuously (2 trip detection logic). (a) No signal from the speed sensor SP2 is input to the ECM while 4 pulses of the No. 1 vehicle speed sensor signal are sent. (b) The vehicle speed is 9 km/h (6 mph) or more for at least 5 sec. (c) The park/neutral position switch is off. (d) The transfer position is not in neutral. |
|
Check the waveform of the ECM connector.
- Standard:
for LHD Terminal No. (Symbol) Tool Setting Condition Specified Condition C45-101 (SP2+) - C45-100 (SP2-) 2 V/DIV., 2 msec./DIV Vehicle speed 20 km/h (12 mph) Refer to illustration for RHD Terminal No. (Symbol) Tool Setting Condition Specified Condition C46-101 (SP2+) - C46-100 (SP2-) 2 V/DIV., 2 msec./DIV Vehicle speed 20 km/h (12 mph) Refer to illustration
MONITOR DESCRIPTION
The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gear shift point and the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.If the ECM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and store a DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display Measurement Item/Range Normal Condition Diagnostic Note SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) - - HINT:
- SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit. - The SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
| 1.INSPECT SPEED SENSOR SP2 INSTALLATION |
Check the speed sensor SP2 installation.
- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
 |
|
| ||||
| OK | |
| 2.INSPECT SPEED SENSOR SP2 |
Disconnect the speed sensor SP2 connector.
 |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 1 - 2 20°C (68°F) 560 to 680 Ω
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM) |
Disconnect the ECM connector.
 |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection Condition Specified Condition C45-101 (SP2+) - C45-100 (SP2-) 20°C (68°F) 560 to 680 Ω C45-101 (SP2+) - Body ground Always 10 kΩ or higher C45-100 (SP2-) - Body ground Always 10 kΩ or higher for RHD Tester Connection Condition Specified Condition C46-101 (SP2+) - C46-100 (SP2-) 20°C (68°F) 560 to 680 Ω C46-101 (SP2+) - Body ground Always 10 kΩ or higher C46-100 (SP2-) - Body ground Always 10 kΩ or higher
|
| ||||
| OK | ||
| ||