Dtc P1630 Communication Error From Vsc To Ecm

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
Cruise Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

INSPECTION PROCEDURE

CHECK CAN COMMUNICATION SYSTEM

CHECK DTC (RADAR CRUISE1)

REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)

CHECK FOR DTCs (RADAR CRUISE1)

DTC P1630 Communication Error from VSC to ECM


DESCRIPTION

The skid control ECU (master cylinder solenoid) sends signals such as cruise control cancel signals and brake demand response signals to the ECM when the dynamic radar cruise control system is operating.

DTC No.
DTC Detection Condition
Trouble Area
P1630
While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (master cylinder solenoid) is logically inconsistent for 0.5 seconds or more.
  1. Communication circuit
  2. Skid control ECU (master cylinder solenoid)
  3. ECM

INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

  1. Using the GTS, check that the CAN communication system is functioning normally.

    OK:
    CAN communication system is functioning normally.
    HINT:
    Refer to CAN Bus Check for the CAN communication system.
    1. for LHD: Click here
    2. for RHD: Click here
    Result:
    Result
    		Proceed to
    OK
    		A
    NG (for LHD)
    		B
    NG (for RHD)
    		C


B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC (RADAR CRUISE1)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Clear the DTCs (Click here).

  1. Make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the system cannot detect the malfunction.
    1. Turn the engine switch on (IG).
    2. Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).
    3. Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.

  1. Enter the following menus: Powertrain / Radar Cruise1 / Trouble Codes.

  1. Check for DTCs (Click here).

    Result:
    Result
    		Proceed to
    DTC P1630 is not output
    		A
    DTC P1630 is output
    		B


B
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)

3.REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)

  1. Replace the skid control ECU (master cylinder solenoid).

    1. for LHD: Click here
    2. for RHD: Click here

NEXT


4.CHECK FOR DTCs (RADAR CRUISE1)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Clear the DTCs (Click here).

  1. Make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the system cannot detect the malfunction.
    1. Turn the engine switch on (IG).
    2. Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).
    3. Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.

  1. Enter the following menus: Powertrain / Radar Cruise1 / Trouble Codes.

  1. Check for DTCs (Click here).

    Result:
    Result
    		Proceed to
    DTC P1630 is not output
    		A
    DTC P1630 is output (for 1UR-FE)
    		B
    DTC P1630 is output (for 3UR-FE)
    		C
    DTC P1630 is output (for 1VD-FTV)
    		D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

END