1Ur-Fe Engine Control. Dtc P0365 Camshaft Position Sensor B Circuit (Bank 1)

The exhaust camshaft VVT sensor (EV1 and EV2 signals) consists of a magnet and MRE (Magnetoresistive Element).
The exhaust camshaft has 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.

DTC No.	DTC Detection Condition	Trouble Area
P0365 P0390	No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).	Open or short in VVT sensor for exhaust camshaft circuit VVT sensor for exhaust camshaft Exhaust camshaft Timing chain jumped tooth ECM
P0367 P0392	Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).	Open or short in VVT sensor for exhaust camshaft circuit VVT sensor for exhaust camshaft Exhaust camshaft Timing chain jumped tooth ECM
P0368 P0393	Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).	Open or short in VVT sensor for exhaust camshaft circuit VVT sensor for exhaust camshaft Exhaust camshaft Timing chain jumped tooth ECM

Land Cruiser. Urj200, 202 Grj200 Vdj200.1Ur-Fe Engine Control.Sfi System.
Dtc
P0365 Camshaft Position Sensor B Circuit (Bank 1)

Reference: Inspection using an oscilloscope

Standard:

for RHD
Tester Connection	Tool Setting	Condition	Specified Condition
C46-110 (NE+) - C46-111 (NE-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C46-69 (EV1+) - C46-68 (EV1-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C46-64 (EV2+) - C46-65 (EV2-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown

for LHD
Tester Connection	Tool Setting	Condition	Specified Condition
C45-110 (NE+) - C45-111 (NE-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C45-69 (EV1+) - C45-68 (EV1-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C45-64 (EV2+) - C45-65 (EV2-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown

HINT:

EV1 and EV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

Start the engine and run it at idle for 10 seconds or more.

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)

Disconnect the VVT sensor connector.

Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
3 (VC2) - Body ground
Engine switch on (IG)
4.5 to 5.0 V
Text in Illustration
*a
Front view of wire harness connector
(to VVT Sensor)
*b
Bank 1
*c
Bank 2

Text in Illustration
*a	Front view of wire harness connector (to VVT Sensor)
*b	Bank 1
*c	Bank 2

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

Disconnect the VVT sensor connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for RHD
Tester Connection	Condition	Specified Condition
C121-1 (EX+) - C46-69 (EV1+)	Always	Below 1 Ω
C121-2 (EX-) - C46-68 (EV1-)	Always	Below 1 Ω
C122-1 (EX+) - C46-64 (EV2+)	Always	Below 1 Ω
C122-2 (EX-) - C46-65 (EV2-)	Always	Below 1 Ω
C121-1 (EX+) or C46-69 (EV1+) - Body ground	Always	10 kΩ or higher
C121-2 (EX-) or C46-68 (EV1-) - Body ground	Always	10 kΩ or higher
C122-1 (EX+) or C46-64 (EV2+) - Body ground	Always	10 kΩ or higher
C122-2 (EX-) or C46-65 (EV2-) - Body ground	Always	10 kΩ or higher

for LHD
Tester Connection	Condition	Specified Condition
C121-1 (EX+) - C45-69 (EV1+)	Always	Below 1 Ω
C121-2 (EX-) - C45-68 (EV1-)	Always	Below 1 Ω
C122-1 (EX+) - C45-64 (EV2+)	Always	Below 1 Ω
C122-2 (EX-) - C45-65 (EV2-)	Always	Below 1 Ω
C121-1 (EX+) or C45-69 (EV1+) - Body ground	Always	10 kΩ or higher
C121-2 (EX-) or C45-68 (EV1-) - Body ground	Always	10 kΩ or higher
C122-1 (EX+) or C45-64 (EV2+) - Body ground	Always	10 kΩ or higher
C122-2 (EX-) or C45-65 (EV2-) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

Check the VVT sensor installation.
OK:
Sensor is installed correctly.

SECURELY REINSTALL SENSOR (Click here)

OK

4.INSPECT EXHAUST CAMSHAFT

Check the teeth of the camshaft.
OK:
Teeth do not have any cracks or deformation.

REPLACE EXHAUST CAMSHAFT (Click here)

OK

5.REPLACE VVT SENSOR

Replace the VVT sensor (Click here).

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS

Connect the GTS to the DLC3.

Turn the engine switch on (IG).

Turn the GTS on.

Clear DTCs (Click here).

Start the engine and idle it for 10 seconds or more.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Read DTCs.

Result
Display (DTC Output)
Proceed to
No DTC is output
A
P0365, P0367, P0368, P0390, P0392 or P0393 is output
B
HINT:
If the engine does not start, replace the ECM.

Result
Display (DTC Output)	Proceed to
No DTC is output	A
P0365, P0367, P0368, P0390, P0392 or P0393 is output	B

REPLACE ECM (Click here)

END

Tester Connection	Switch Condition	Specified Condition
3 (VC2) - Body ground	Engine switch on (IG)	4.5 to 5.0 V