Entry And Start System (For Entry Function) Rear Door Rh Entry Lock And Unlock Functions Do Not Operate

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK POWER DOOR LOCK OPERATION

READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)

CHECK WAVE ENVIRONMENT

PERFORM KEY DIAGNOSTIC MODE INSPECTION

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)

CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE)

CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)

REPLACE DOOR ELECTRICAL KEY OSCILLATOR

CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

REPLACE REAR DOOR OUTSIDE HANDLE

CHECK REAR DOOR OUTSIDE HANDLE OPERATION

DESCRIPTION

HINT:

For vehicles with entry function for rear doors.

WIRING DIAGRAM

INSPECTION PROCEDURE

1. When the master switch assembly door control switch is operated, check that the locked doors unlock.
   

   OK:

   Door locks operate normally.
   

1. Connect the intelligent tester to the DLC3.
   

2. Turn the engine switch on (IG).
   

3. Turn the intelligent tester on.
   

4. Enter the following menus: Body / Main Body / Data List.
   

5. Read the Data List according to the display on the intelligent tester.
   

   1. for LHD
      
      

      Main Body

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      PR Door Lock Position SW	Passenger side rear door lock position switch signal / ON or OFF	ON: Passenger side rear door unlocked OFF: Passenger side rear door locked	-

      OK:

      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
      

   2. for RHD
      
      

      Main Body

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      DR Door Lock Position SW	Driver side rear door lock position switch signal / ON or OFF	ON: Driver side rear door unlocked OFF: Driver side rear door locked	-

      OK:

      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
      

1. Using the intelligent tester, read the Data List.
   

   1. for LHD
      
      

      Entry & Start

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Pr-Door Touch Sensor	Passenger side rear door touch sensor / ON or OFF	ON: Touch sensor touched OFF: Touch sensor not touched	-
      Pr-Door Trigger Switch	Passenger side rear door outside handle lock switch / ON or OFF	ON: Entry lock switch pushed OFF: Entry lock switch not pushed	-

   2. for RHD
      
      

      Entry & Start

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Dr-Door Touch Sensor	Driver side rear door touch sensor / ON or OFF	ON: Touch sensor touched OFF: Touch sensor not touched	-
      Dr-Door Trigger Switch	Driver side rear door outside handle lock switch / ON or OFF	ON: Entry lock switch pushed OFF: Entry lock switch not pushed	-

1. Bring the electrical key transmitter near the rear door outside handle RH, and perform a rear door RH entry lock and unlock operation check.
   

   NOTICE:

   If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

   HINT:

   1. When the electrical key transmitter is brought near the rear door outside handle RH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
      
   2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
      

   Result

   Result	Proceed to
   Operation check fails	A
   Operation check is normal	B

1. Diagnostic mode inspection (rear door electrical key oscillator RH).
   

   1. Connect the intelligent tester to the DLC3.
      

   2. Turn the engine switch on (IG).
      

   3. Turn the intelligent tester on.
      

   4. Enter the following menus:
      for LHD
      Select: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side Rear.
      for RHD
      Select: Body / Entry & Start / Key Communication Check / Overhead + Driver Side Rear.
      

   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
      

      HINT:

      If the buzzer sounds, it can be determined that the rear RH seat outside transmitter is operating normally.

      OK:

      Wireless door lock buzzer sounds.
      

1. Disconnect the E30 ECU connector.
   

2. Disconnect the z26 oscillator connector.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   for LHD:

   Tester Connection	Condition	Specified Condition
   E30-2 (SEL4) - z26-4 (SEL)	Always	Below 1 Ω
   E30-10 (CLG4) - z26-10 (CLG)	Always	Below 1 Ω
   E30-11 (CG4B) - z26-5 (CLGB)	Always	Below 1 Ω
   E30-2 (SEL4) - Body ground	Always	10 kΩ or higher
   E30-10 (CLG4) - Body ground	Always	10 kΩ or higher
   E30-11 (CG4B) - Body ground	Always	10 kΩ or higher

   for RHD:

   Tester Connection	Condition	Specified Condition
   E30-1 (SEL3) - z26-4 (SEL)	Always	Below 1 Ω
   E30-8 (CLG3) - z26-10 (CLG)	Always	Below 1 Ω
   E30-9 (CG3B) - z26-5 (CLGB)	Always	Below 1 Ω
   E30-1 (SEL3) - Body ground	Always	10 kΩ or higher
   E30-8 (CLG3) - Body ground	Always	10 kΩ or higher
   E30-9 (CG3B) - Body ground	Always	10 kΩ or higher

1. Disconnect the z25 handle connector.
   

2. Disconnect the z26 oscillator connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   z25-2 (ANT2) - z26-8 (ANT2)	Always	Below 1 Ω
   z25-5 (ANT1) - z26-3 (ANT1)	Always	Below 1 Ω
   z25-2 (ANT2) - Body ground	Always	10 kΩ or higher
   z25-5 (ANT1) - Body ground	Always	10 kΩ or higher

1. Disconnect the z26 oscillator connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Condition	Specified Condition
   z26-1 (B) - z26-7 (GND)	Always	11 to 14 V

1. Replace the door electrical key oscillator (Click here).
   

1. Check that the entry function operates normally.
   

   OK:

   Operates normally.
   

1. Replace the rear door outside handle (Click here).
   

1. Check that the entry function operates normally.
   

   OK:

   Operates normally.