Automatic Transmission System (For 3Ur-Fe) Pattern Select Switch Power Mode Circuit

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT PATTERN SELECT (PWR) SWITCH

CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)

CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)

AUTOMATIC TRANSMISSION SYSTEM (for 3UR-FE) - Pattern Select Switch Power Mode Circuit


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.
By following the programs corresponding to the signals from the pattern select switch, the park/neutral position switch and other various sensors, the ECM switches the shift solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe).Automatic Transmission System (For 3Ur-Fe) Pattern Select Switch Power Mode Circuit


INSPECTION PROCEDURE

When the pattern select (PWR) switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the pattern select (2nd) switch once again.
1.INSPECT PATTERN SELECT (PWR) SWITCH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe).Automatic Transmission System (For 3Ur-Fe) Pattern Select Switch Power Mode Circuit

  1. Remove the suspension control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    3 (P) - 16 (E)
    		Pattern select (PWR) switch on
    		Below 1 Ω
    3 (P) - 16 (E)
    		Pattern select (PWR) switch off
    		10 kΩ or higher
    Text in Illustration
    *a
    		Component without harness connected
    (Suspension Control Switch)


NG
REPLACE PATTERN SELECT (PWR) SWITCH (SUSPENSION CONTROL SWITCH) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe).Automatic Transmission System (For 3Ur-Fe) Pattern Select Switch Power Mode Circuit

  1. Disconnect the suspension control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    V4-16 (E) - Body ground
    		Always
    		Below 1 Ω
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Suspension Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe).Automatic Transmission System (For 3Ur-Fe) Pattern Select Switch Power Mode Circuit

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A38-51 (PWR) - Body ground
    		Pattern select (PWR) switch on
    		Below 1 Ω
    A38-51 (PWR) - Body ground
    		Pattern select (PWR) switch off
    		10 kΩ or higher
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)