Tire Pressure Warning System Data List / Active Test

Suspension. Land Cruiser. Urj200, 202 Grj200 Vdj200
Tire Pressure Monitoring. Land Cruiser. Urj200, 202 Grj200 Vdj200
  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Tire Pressure Warning System -- Data List / Active Test



READ DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  6. According to the display on the GTS, read the Data List.

    Tire Pressure Monitor
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mode Status
    Tire pressure warning system mode/
    NORMAL or TEST
    NORMAL: Normal mode
    TEST: Test mode
    -
    Main Tire
    Number of main tire IDs to be registered/
    4 or 5
    5 displayed
    -
    2nd Tire
    Number of 2nd tire IDs to be registered
    4 or 5
    5 displayed
    -
    Initialization Switch
    Tire pressure warning reset switch/
    ON or OFF
    ON: Switch on
    OFF: Switch off
    -
    Vehicle Speed
    Vehicle speed reading/
    min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on the combination meter assembly
    Registered ID 1 Code
    Registered ID1 code/
    min.: 0, max.: FFFFFFF*1
    ID No. registered for transmitter ID1 displayed
    -
    Registered ID 2 Code
    Registered ID2 code/
    min.: 0, max.: FFFFFFF*1
    ID No. registered for transmitter ID2 displayed
    -
    Registered ID 3 Code
    Registered ID3 code/
    min.: 0, max.: FFFFFFF*1
    ID No. registered for transmitter ID3 displayed
    -
    Registered ID 4 Code
    Registered ID4 code/
    min.: 0, max.: FFFFFFF*1
    ID No. registered for transmitter ID4 displayed
    -
    Registered ID 5 Code
    Registered ID5 code/
    min.: 0, max.: FFFFFFF*1
    ID No. registered for transmitter ID5 displayed
    -
    ID 1 Temperature in Tire
    ID1 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 2 Temperature in Tire
    ID2 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 3 Temperature in Tire
    ID3 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 4 Temperature in Tire
    ID4 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 5 Temperature in Tire
    ID5 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    Initialization Switch Info
    Tire pressure warning reset switch setting information/
    WITH or WITHOUT
    WITH
    -
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*2
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*2
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*2
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*2
    ID 5 Tire Inflation Pressure
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*2
    Threshold of Low pressure (Lower Limit)
    Tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Specified tire pressure warning threshold lower limit displayed
    If N/A is displayed, data has not been received.*2
    ID 1 Initial Threshold of Low-pressure
    ID1 initial threshold of low-pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Initial threshold of low pressure
    If N/A is displayed, data has not been received.*2
    ID 2 Initial Threshold of Low-pressure
    ID2 initial threshold of low-pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Initial threshold of low pressure
    If N/A is displayed, data has not been received.*2
    ID 3 Initial Threshold of Low-pressure
    ID3 initial threshold of low-pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Initial threshold of low pressure
    If N/A is displayed, data has not been received.*2
    ID 4 Initial Threshold of Low-pressure
    ID4 initial threshold of low-pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Initial threshold of low pressure
    If N/A is displayed, data has not been received.*2
    ID 5 Initial Threshold of Low-pressure
    ID5 initial threshold of low-pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Initial threshold of low pressure
    If N/A is displayed, data has not been received.*2
    Sensor ID Status
    Status of ID selection/
    Main or 2nd
    Status of ID selection
    -
    Sensor ID Switch Function
    Information on whether there is ID switching function or not/
    Without or With
    Without: ID switching function is not equipped
    With: ID switching function is equipped
    -
    ID 1 Tire Position
    ID1 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging
    ID1 tire position is displayed
    If no tire position information is stored, "No Information" will be displayed.
    ID 2 Tire Position
    ID2 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging
    ID2 tire position is displayed
    If no tire position information is stored, "No Information" will be displayed.
    ID 3 Tire Position
    ID3 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging
    ID3 tire position is displayed
    If no tire position information is stored, "No Information" will be displayed.
    ID 4 Tire Position
    ID4 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging
    ID4 tire position is displayed
    If no tire position information is stored, "No Information" will be displayed.
    ID 5 Tire Position
    ID5 Tire Position/No Information or FL or FR or RL or RR or Spare or Judging
    ID5 tire position is displayed
    If no tire position information is stored, "No Information" will be displayed.
    ID 1 - FL Wheel Speed Synchronization Count
    ID1 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 1 - FR Wheel Speed Synchronization Count
    ID1 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 1 - RL Wheel Speed Synchronization Count
    ID1 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 1 - RR Wheel Speed Synchronization Count
    ID1 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 2 - FL Wheel Speed Synchronization Count
    ID2 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 2 - FR Wheel Speed Synchronization Count
    ID2 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 2 - RL Wheel Speed Synchronization Count
    ID2 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 2 - RR Wheel Speed Synchronization Count
    ID2 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 3 - FL Wheel Speed Synchronization Count
    ID3 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 3 - FR Wheel Speed Synchronization Count
    ID3 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 3 - RL Wheel Speed Synchronization Count
    ID3 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 3 - RR Wheel Speed Synchronization Count
    ID3 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 4 - FL Wheel Speed Synchronization Count
    ID4 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 4 - FR Wheel Speed Synchronization Count
    ID4 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 4 - RL Wheel Speed Synchronization Count
    ID4 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 4 - RR Wheel Speed Synchronization Count
    ID4 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 5 - FL Wheel Speed Synchronization Count
    ID5 - FL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 5 - FR Wheel Speed Synchronization Count
    ID5 - FR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 5 - RL Wheel Speed Synchronization Count
    ID5 - RL Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    ID 5 - RR Wheel Speed Synchronization Count
    ID5 - RR Wheel Speed Synchronization Count/min.: 0, max.: 255
    Actual Synchronization Count
    -
    Number of Trouble Code
    Number of DTCs recorded/min.: 0, max.: 255
    Min.: 0, Max.: -
    -

    HINT:
    *1: Displayed only when the ID No. is not registered.
    *2: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25) (Click here).

PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  6. Perform the Active Test according to the display on the GTS.

    Combination Meter
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Tire Pressure Warning System
    Tire pressure warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.