Tire Pressure Warning System Data List / Active Test

Suspension. Land Cruiser. Urj200, 202 Grj200 Vdj200
Tire Pressure Monitoring. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Tire Pressure Warning System -- Data List / Active Test



READ DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  6. According to the display on the GTS, read the Data List.

    Tire Pressure Monitor
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mode Status
    		Tire pressure warning system mode/
    NORMAL or TEST
    		NORMAL: Normal mode
    TEST: Test mode
    		-
    Main Tire
    		Number of main tire ID to be registered/
    4 or 5
    		5 displayed
    		-
    2nd Tire
    		Number of 2nd tire ID to be registered/
    4 or 5
    		5 displayed
    		-
    Initialization Switch
    		Tire pressure warning reset switch/
    ON or OFF
    		ON: Switch on
    OFF: Switch off
    		-
    Vehicle Speed
    		Vehicle speed reading/
    min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    		Actual vehicle speed
    		Speed indicated on the combination meter assembly
    Registered ID 1 Code
    		Registered ID1 code/
    min.: 0, max.: FFFFFFF*1
    		ID No. registered for transmitter ID1 displayed
    		-
    Registered ID 2 Code
    		Registered ID2 code/
    min.: 0, max.: FFFFFFF*1
    		ID No. registered for transmitter ID2 displayed
    		-
    Registered ID 3 Code
    		Registered ID3 code/
    min.: 0, max.: FFFFFFF*1
    		ID No. registered for transmitter ID3 displayed
    		-
    Registered ID 4 Code
    		Registered ID4 code/
    min.: 0, max.: FFFFFFF*1
    		ID No. registered for transmitter ID4 displayed
    		-
    Registered ID 5 Code
    		Registered ID5 code/
    min.: 0, max.: FFFFFFF*1
    		ID No. registered for transmitter ID5 displayed
    		-
    ID 1 Temperature in Tire
    		ID1 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    		Actual tire temperature
    		If -40°C (-40°F) is displayed, data has not been received.
    ID 2 Temperature in Tire
    		ID2 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    		Actual tire temperature
    		If -40°C (-40°F) is displayed, data has not been received.
    ID 3 Temperature in Tire
    		ID3 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    		Actual tire temperature
    		If -40°C (-40°F) is displayed, data has not been received.
    ID 4 Temperature in Tire
    		ID4 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    		Actual tire temperature
    		If -40°C (-40°F) is displayed, data has not been received.
    ID 5 Temperature in Tire
    		ID5 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    		Actual tire temperature
    		If -40°C (-40°F) is displayed, data has not been received.
    Initialization Switch Info
    		Tire pressure warning reset switch setting information/
    WITH or WITHOUT
    		WITH
    		-
    ID 1 Tire Inflation Pressure
    		ID1 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Actual tire inflation pressure
    		If N/A is displayed, data has not been received.*2
    ID 2 Tire Inflation Pressure
    		ID2 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Actual tire inflation pressure
    		If N/A is displayed, data has not been received.*2
    ID 3 Tire Inflation Pressure
    		ID3 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Actual tire inflation pressure
    		If N/A is displayed, data has not been received.*2
    ID 4 Tire Inflation Pressure
    		ID4 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Actual tire inflation pressure
    		If N/A is displayed, data has not been received.*2
    ID 5 Tire Inflation Pressure
    		ID5 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Actual tire inflation pressure
    		If N/A is displayed, data has not been received.*2
    Threshold of Low-pressure (Lower Limit)
    		min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Specified tire pressure warning threshold lower limit displayed
    		-
    ID 1 Initial Threshold of Low-pressure
    		ID1 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Tire pressure after initialization
    		-
    ID 2 Initial Threshold of Low-pressure
    		ID2 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Tire pressure after initialization
    		-
    ID 3 Initial Threshold of Low-pressure
    		ID3 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Tire pressure after initialization
    		-
    ID 4 Initial Threshold of Low-pressure
    		ID4 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Tire pressure after initialization
    		-
    ID 5 Initial Threshold of Low-pressure
    		ID5 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    		Tire pressure after initialization
    		-
    Sensor ID Status
    		Status of ID selection/
    Main or 2nd
    		Status of ID selection
    		-
    Sensor ID Switch Function
    		Information on whether there is ID switching function or not/
    Without or With
    		With
    		-
    Number of Trouble Code
    		Number of DTCs recorded/
    min.: 0, max.: 255
    		0
    		-

    HINT:
    1. *1: Displayed only when the ID No. is not registered.
    2. *2: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 (Click here).
    3. The wheel position cannot be determined from ID1 through ID5 on the Data List.

PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  6. Check the operation by referring to the table below.

    Combination Meter
    Tester Display
    		Test Part
    		Control Range
    Indicat. Tire Pressure Warning System
    		Tire pressure warning light
    		OFF or ON