Dtc B2282 Vehicle Speed Signal Malfunction

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)

REPLACE MAIN BODY ECU

DTC B2282 Vehicle Speed Signal Malfunction

DTC B2283 Vehicle Speed Sensor Malfunction


DESCRIPTION

The main body ECU and the combination meter are connected with a cable and the CAN communication line. DTC B2282 is stored when signals, transmitted through the cable and communication line, do not match.

DTC Code
Detection Condition
Trouble Area
B2282
When the following conditions are met:
  1. Signals between the main body ECU and combination meter are inconsistent.
  1. A malfunction is detected in the circuit between the vehicle speed sensor and combination meter.
  1. Main body ECU
  1. Combination meter assembly
  1. Harness or connector
The skid control ECU converts signals from the speed sensor into 4-pulse signals and sends them to the combination meter. After these signals are converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, they are then transmitted to the main body ECU. The main body ECU determines the vehicle speed based on the frequencies of these pulse signals.

DTC Code
Detection Condition
Trouble Area
B2283
When both of the conditions below are met:
  1. Vehicle speed decreases significantly.
  1. Vehicle speed does not correspond with engine speed.
  1. Main body ECU
  1. Combination meter assembly
  1. Speed sensor
  1. Skid control ECU
  1. Harness or connector

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function). Dtc B2282 Vehicle Speed Signal Malfunction


WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function). Dtc B2282 Vehicle Speed Signal Malfunction


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL)

  1. Use the Data List to check if the vehicle speed signal is functioning properly.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Vehicle Speed Signal
    		Vehicle speed signal/STOP or RUN
    		STOP: Vehicle stopped
    RUN: Vehicle running
    		-
    Result
    Result
    		Proceed to
    Display on the intelligent tester does not change according to vehicle condition
    		A
    Display on the intelligent tester changes according to vehicle condition
    		B


B
REPLACE MAIN BODY ECU
A


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function). Dtc B2282 Vehicle Speed Signal Malfunction

  1. Disconnect the E3 main body ECU connector.

  1. Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E3-9 (SPD) - E7-4 (+S)
    		Always
    		Below 1 Ω
    E3-9 (SPD) or E7-4 (+S) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE MAIN BODY ECU

  1. Temporarily replace the main body ECU with a new or normally functioning one.

  1. Check whether DTC B2282 and B2283 are output.

    Result
    Result
    		Proceed to
    DTC not output
    		A
    DTC output (w/ Multi-information Display)
    		B
    DTC output (w/o Multi-information Display)
    		C


B
REPLACE COMBINATION METER (Click here)

C
REPLACE COMBINATION METER (Click here)
A

END