DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK OPERATION OF DOOR COURTESY LIGHT
INSPECT COWL SIDE JUNCTION BLOCK LH (DOME CUT RELAY)
CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT - BATTERY)
INSPECT FRONT DOOR COURTESY LIGHT LH
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
INSPECT FRONT DOOR COURTESY LIGHT RH
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
INSPECT REAR DOOR COURTESY LIGHT LH
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
INSPECT REAR DOOR COURTESY LIGHT RH
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
LIGHTING SYSTEM - Door Courtesy Light Circuit |
DESCRIPTION
The door courtesy light turns on when the door is opened and turns off when closed.
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
| 1.CHECK OPERATION OF DOOR COURTESY LIGHT |
When a door is opened, check that the following lights do not illuminate.
ResultResult
| Proceed to
|
All door courtesy light does not illuminate
| A
|
Front door courtesy light LH does not illuminate
| B
|
Front door courtesy light RH does not illuminate
| C
|
Rear door courtesy light LH does not illuminate
| D
|
Rear door courtesy light RH does not illuminate
| E
|
| 2.INSPECT COWL SIDE JUNCTION BLOCK LH (DOME CUT RELAY) |
Remove the cowl side junction block LH.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
2F-1 - 2J-11
| Battery voltage not applied to terminals 2F-1 and A-23
| 10 kΩ or higher
|
Battery voltage applied to terminals 2F-1 and A-23
| Below 1 Ω
|
| | REPLACE COWL SIDE JUNCTION BLOCK LH (DOME CUT RELAY) |
|
|
| 3.CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT - BATTERY) |
Disconnect the I13, I5, J12 and J5 ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Switch Condition
| Specified Condition
|
I13-1 - Body ground
| Always
| 11 to 14 V
|
J12-1 - Body ground
|
I5-1 - Body ground
|
J5-1 - Body ground
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
|
|
| PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE (Click here) |
|
| 4.INSPECT FRONT DOOR COURTESY LIGHT LH |
Remove the door courtesy light connector.
Check that the door courtesy light comes on.
- OK:
Measurement Condition
| Specified Condition
|
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
| Light illumination
|
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the E117 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Condition
| Specified Condition
|
E117-1 (FLCL) - Body ground
| Ignition switch ON
| 11 to 14 V
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
|
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
| 6.INSPECT FRONT DOOR COURTESY LIGHT RH |
Remove the door courtesy light connector.
Check that the door courtesy light comes on.
- OK:
Measurement Condition
| Specified Condition
|
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
| Light illumination
|
| 7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the E117 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Condition
| Specified Condition
|
E117-17 (FRCL) - Body ground
| Ignition switch ON
| 11 to 14 V
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
|
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
| 8.INSPECT REAR DOOR COURTESY LIGHT LH |
Remove the door courtesy light connector.
Check that the door courtesy light comes on.
- OK:
Measurement Condition
| Specified Condition
|
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
| Light illumination
|
| 9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the E137 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Condition
| Specified Condition
|
E137-2 (LCYL) - Body ground
| Ignition switch ON
| 11 to 14 V
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
|
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
| 10.INSPECT REAR DOOR COURTESY LIGHT RH |
Remove the door courtesy light connector.
Check that the door courtesy light comes on.
- OK:
Measurement Condition
| Specified Condition
|
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
| Light illumination
|
| 11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the E137 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Condition
| Specified Condition
|
E137-1 (RCYL) - Body ground
| Ignition switch ON
| 11 to 14 V
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
|
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
