Mirror (Ext). Outer Rear View Mirror Inspection

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200

Mirror (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror)
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror)
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror)
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror)

Outer Rear View Mirror -- Inspection

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror)

Apply battery voltage and check the operation of the mirror.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 3 (MV) Battery negative (-) → Terminal 1 (M+)	Turns upward (A)
Battery positive (+) → Terminal 1 (M+) Battery negative (-) → Terminal 3 (MV)	Turns downward (B)
Battery positive (+) → Terminal 2 (MH) Battery negative (-) → Terminal 1 (M+)	Turns left (C)
Battery positive (+) → Terminal 1 (M+) Battery negative (-) → Terminal 2 (MH)	Turns right (D)

If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

w/ Side Turn Signal Light:
1. Check the side turn light assembly.
2. Apply battery voltage to the terminals of the connector, and check the illumination condition.
  OK:
  Measurement Connection
  Specified Condition
  Battery positive (+) → Terminal 4 (TRNL)
  Negative (-) end of the battery → Terminal 5 (GND)
  Side turn light illuminates
  If the result is not as specified, check the side turn signal light assembly LH (Click here).
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly LH)

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror)

Apply battery voltage and check the operation of the mirror.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 3 (MV) Battery negative (-) → Terminal 1 (M+)	Turns upward (A)
Battery positive (+) → Terminal 1 (M+) Battery negative (-) → Terminal 3 (MV)	Turns downward (B)
Battery positive (+) → Terminal 2 (MH) Battery negative (-) → Terminal 1 (M+)	Turns right (C)
Battery positive (+) → Terminal 1 (M+) Battery negative (-) → Terminal 2 (MH)	Turns left (D)

If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

/ Side Turn Signal Light:
1. Check the side turn light assembly.
2. Apply battery voltage to the terminals of the connector, and check the illumination condition.
  OK:
  Measurement Connection
  Specified Condition
  Battery positive (+) → Terminal 4 (TRNR)
  Negative (-) end of the battery → Terminal 5 (GND)
  Side turn light illuminates
  If the result is not as specified, check the side turn signal light assembly RH (Click here).
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly RH)

3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror)

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:

Measurement Condition	Mirror Position	Specified Condition
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Forward position A	Moves from A to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Forward position A	Does not move
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Position between forward position A and driving position C	Moves from B to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Position between forward position A and driving position C	Moves from B to forward position A
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Driving position C	Moves from C to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Driving position C	Does not move
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Position between driving position C and retracted position E	Moves from D to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Position between driving position C and retracted position E	Moves from D to driving position C
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Retracted position E	Does not move
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Retracted position E	Moves from E to driving position C

NOTICE:

Disconnect and reconnect the battery between each mirror position check.

Do not apply battery voltage when moving the mirror by hand into each mirror position.

If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

Apply battery voltage and check the operation of the mirror.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 7 (MV) Battery negative (-) → Terminal 8 (M+)	Turns upward
Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 7 (MV)	Turns downward
Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 8 (M+)	Turns left
Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 9 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

w/ Mirror Heater:
1. Check the mirror heater.
2. Measure the resistance according to the value (s) in the table below.
  Standard Resistance:
  Tester Connection
  Condition
  Specified Condition
  Terminal 6 (+) - Terminal 17 (-)
  25°C (75°F)
  3.0 to 3.9 Ω
  If the result is not as specified, replace the outer rear view mirror assembly LH.
3. Apply battery voltage and check the operation of the mirror heater.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 6 (+)
  Battery negative (-) → Terminal 17 (-)
  Mirror becomes warm
  HINT:
  It will take a short time for the mirror to become warm.
  If the result is not as specified, replace the outer rear view mirror assembly LH.
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly LH)

Check the side turn light assembly.
1. Apply battery voltage to the terminals of the connector, and check the illumination condition.
  OK:
  Measurement Connection
  Specified Condition
  Battery positive (+) → Terminal 4 (TRNL)
  Negative (-) end of the battery → Terminal 15 (GND)
  Side turn light illuminates
  If the result is not as specified, check the side turn signal light assembly LH (Click here).
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly LH)

w/EC Mirror:
1. Check the EC mirror operation.
2. Connect 1.5 V dry-cell battery.
3. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 5 (EC+)
  Battery negative (-) → Terminal 16 (EC-)
  Mirror surface becomes dark
  If the result is not as specified, replace the outer rear view mirror assembly LH.
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly LH)

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror)

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:

Measurement Condition	Mirror Position	Specified Condition
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Forward position A	Moves from A to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Forward position A	Does not move
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Position between forward position A and driving position C	Moves from B to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Position between forward position A and driving position C	Moves from B to forward position A
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Driving position C	Moves from C to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Driving position C	Does not move
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Position between driving position C and retracted position E	Moves from D to retracted position E
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Position between driving position C and retracted position E	Moves from D to driving position C
Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF)	Retracted position E	Does not move
Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF)	Retracted position E	Moves from E to driving position C

NOTICE:

Disconnect and reconnect the battery between each mirror position check.

Do not apply battery voltage when moving the mirror by hand into each mirror position.

If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

Apply battery voltage and check the operation of the mirror.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 7 (MV) Battery negative (-) → Terminal 8 (M+)	Turns upward
Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 7 (MV)	Turns downward
Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 8 (M+)	Turns left
Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 9 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

w/ Mirror Heater:
1. Check the mirror heater.
2. Measure the resistance according to the value (s) in the table below.
  Standard Resistance:
  Tester Connection
  Condition
  Specified Condition
  Terminal 6 (+) - Terminal 17 (-)
  25°C (75°F)
  3.0 to 3.9 Ω
  If the result is not as specified, replace the outer rear view mirror assembly RH.
3. Apply battery voltage and check the operation of the mirror heater.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 6 (+)
  Battery negative (-) → Terminal 17 (-)
  Mirror becomes warm
  HINT:
  It will take a short time for the mirror to become warm.
  If the result is not as specified, replace the outer rear view mirror assembly.
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly RH)

Check the side turn light assembly.
1. Apply battery voltage to the terminals of the connector, and check the illumination condition.
  OK:
  Measurement Connection
  Specified Condition
  Battery positive (+) → Terminal 4 (TRNR)
  Negative (-) end of the battery → Terminal 15 (GND)
  Side turn light illuminates
  If the result is not as specified, check the side turn signal light assembly RH (Click here).
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly RH)

w/EC Mirror:
1. Check the EC mirror operation.
2. Connect 1.5 V dry-cell battery.
3. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 5 (EC+)
  Battery negative (-) → Terminal 16 (EC-)
  Mirror surface becomes dark
  If the result is not as specified, replace the outer rear view mirror assembly RH.
  Text in Illustration
  *a
  Component without harness connected
  (Outer Rear View Mirror Assembly RH)

Measurement Connection	Specified Condition
Battery positive (+) → Terminal 4 (TRNL) Negative (-) end of the battery → Terminal 5 (GND)	Side turn light illuminates

Measurement Connection	Specified Condition
Battery positive (+) → Terminal 4 (TRNR) Negative (-) end of the battery → Terminal 5 (GND)	Side turn light illuminates

Tester Connection	Condition	Specified Condition
Terminal 6 (+) - Terminal 17 (-)	25°C (75°F)	3.0 to 3.9 Ω

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 6 (+) Battery negative (-) → Terminal 17 (-)	Mirror becomes warm

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 5 (EC+) Battery negative (-) → Terminal 16 (EC-)	Mirror surface becomes dark