Sliding Roof System Sliding Roof Control Switch Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF OPERATION)

READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF SWITCH)

INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (Click here).
   
   

   Sliding Roof

   Tester Display	Test Part	Control Range	Diagnostic Note
   Slide Roof	Operate sliding roof SLIDE CLOSE/TILT UP	CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs OFF: Sliding roof is not operating	Be careful to avoid injuries as this test causes vehicle parts to move.
   Slide Roof	Operate sliding roof SLIDE OPEN/TILT DOWN	OPEN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs OFF: Sliding roof is not operating	Be careful to avoid injuries as this test causes vehicle parts to move.

OK:

Sliding roof operates normally.

1. Use the Data List to check if the sliding roof switch is functioning properly (Click here).
   
   

   Sliding Roof

   Item	Measurement Item/Range	Normal Condition	Diagnostic Note
   Open Switch	Sliding roof switch open signal/ON or OFF	ON: OPEN switch is pressed OFF: OPEN switch is not pressed	-
   Close Switch	Sliding roof switch close signal/ON or OFF	ON: CLOSE switch is pressed OFF: CLOSE switch is not pressed	-
   Up Switch	Sliding roof switch tilt up signal/ON or OFF	ON: UP switch is pressed OFF: UP switch is not pressed	-
   Down Switch	Sliding roof switch tilt down signal/ON or OFF	ON: DOWN switch is pressed OFF: DOWN switch is not pressed	-

OK:

When the switch is operating, the intelligent tester should display as shown in the table.

1. Remove the map light (Click here).
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition	Specified Condition
   19 (UP) - 17 (GND9)	UP switch is pressed	Below 1 Ω
   19 (UP) - 17 (GND9)	UP switch is not pressed	10 kΩ or higher
   18 (DOWN) - 17 (GND9)	DOWN switch is pressed	Below 1 Ω
   18 (DOWN) - 17 (GND9)	DOWN switch is not pressed	10 kΩ or higher
   8 (OPN) - 17 (GND9)	OPEN switch is pressed	Below 1 Ω
   8 (OPN) - 17 (GND9)	OPEN switch is not pressed	10 kΩ or higher
   7 (CLS) - 17 (GND9)	CLOSE switch is pressed	Below 1 Ω
   7 (CLS) - 17 (GND9)	CLOSE switch is not pressed	10 kΩ or higher

1. Disconnect the R5 drive gear connector.
   

2. Disconnect the R7 map light connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   R5-10 (UP) - R7-19 (UP)	Always	Below 1 Ω
   R5-8 (DWN) - R7-18 (DOWN)	Always	Below 1 Ω
   R5-7 (OPN) - R7-8 (OPN)	Always	Below 1 Ω
   R5-9 (CLS) - R7-7 (CLS)	Always	Below 1 Ω
   R7-17 (GND9) - Body ground	Always	Below 1 Ω
   R5-2 (E) - Body ground	Always	Below 1 Ω
   R5-10 (UP) or R7-19 (UP) - Body ground	Always	10 kΩ or higher
   R5-8 (DWN) or R7-18 (DOWN) - Body ground	Always	10 kΩ or higher
   R5-7 (OPN) or R7-8 (OPN) - Body ground	Always	10 kΩ or higher
   R5-9 (CLS) or R7-7 (CLS) - Body ground	Always	10 kΩ or higher