Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
1Ur-Fe Engine Control. Land Cruiser. Urj200, 202 Grj200 Vdj200
READ VALUE USING GTS (+BM VOLTAGE)
CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
DTC P2118 Throttle Actuator Control Motor Current Range / Performance |
DESCRIPTION
The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the engine switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.
- HINT:
- The ETCS does not use a throttle cable.
| DTC No. | DTC Detection Condition | Trouble Area |
| P2118 | Open in the ETCS power source (+BM) circuit (1 trip detection logic). |
|
MONITOR DESCRIPTION
The ECM monitors the battery supply voltage applied to the throttle actuator.When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.
CONFIRMATION DRIVING PATTERN
- Connect the GTS to the DLC3.
- Turn the engine switch on (IG) and turn the GTS on.
- Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
- Turn the engine switch off and wait for at least 30 seconds.
- Turn the engine switch on (IG) and turn the GTS on [A].
- Start the engine.
- Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].
- Check that 16 seconds or more have elapsed since the engine was started.
- Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
- Read the pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P2118.
- Check the DTC judgment result.
GTS Display Description NORMAL - DTC judgment completed
- System normal
ABNORMAL - DTC judgment completed
- System abnormal
INCOMPLETE - DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A - Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and , if necessary, drive the vehicle for a period of time.
- DTC judgment completed
FAIL-SAFE
When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.The ECM continues operating in fail-safe mode until a pass condition is detected, and the engine switch is then turned off.
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1.READ VALUE USING GTS (+BM VOLTAGE) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.
Read the value displayed on the GTS.
Result Result Proceed to Below 11 V or higher than 14 V A 11 to 14 V B
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for RHD Tester Connection Condition Specified Condition C46-41 (+BM) - Body ground Always 11 to 14 V for LHD Tester Connection Condition Specified Condition C45-41 (+BM) - Body ground Always 11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RHD Tester Connection Condition Specified Condition C46-81 (E1) - Body ground Always Below 1 Ω C46-82 (ME01) - Body ground Always Below 1 Ω for LHD Tester Connection Condition Specified Condition C45-81 (E1) - Body ground Always Below 1 Ω C45-82 (ME01) - Body ground Always Below 1 Ω
|
| ||||
| OK | ||
| ||