Roof Headlining (For Sedan) Installation

Install the roof headlining into the front door.

w/ Curtain Shield Airbag:

1. Engage the 4 hooks.
   

2. Install the 2 clips.
   

w/o Curtain Shield Airbag:

1. Engage the 2 claws and 4 hooks.
   

2. Install the 2 clips.
   

Connect the antenna connector.

Install the clamp.

Connect the roof wire connector.

Install the 2 clamps.

Connect the map light connector.

Engage the 4 claws and install the map light.

Engage the 4 claws and install the room light switch base.

Install the roof wire into the claw of the room light.

Engage the 4 claws and install the room light.

Engage the 2 claws and install the cover.

HINT:

Use the same procedure for both sides.

Engage the 4 claws and install the room light lens.

Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.

Engage the 2 springs and install the visor.

Install the visor shaft into the visor holder.

Engage the 4 claws and install a new visor bracket cover.

Engage the 2 springs and install the assist grip.

Engage the 2 claws and install the assist grip cover.

Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

Engage the 2 hinges with the instrument panel open.

Close the instrument panel box.

Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

Engage the 5 claws at the front side of the instrument panel.

Engage the 7 clips at the rear side of the instrument panel.

Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf} for bolt <C>

Connect the passenger airbag connector and clamp.

Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

NOTICE:

Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

Install the 2 glove compartment door stoppers onto the glove compartment door.

Install the combination meter assembly with the 2 screws.

NOTICE:

Install the meter by inserting the ribbed portions of the meter between the instrument panel and meter cluster.

Connect the 2 connectors.

Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

Engage the 5 claws and 5 clips and install the instrument cluster finish panel.

Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.

Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.

Engage the 4 claws and install the rear console box.

Install the 2 bolts and 2 screws.

Connect the clamp.

Install the console box carpet.

Connect the connector.

Engage the 3 clips and 3 claws and install the console upper rear panel.

Engage the 5 clips and the claw and install the upper console panel.

Install the shift lever knob.

Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.

w/ Curtain Shield Airbag:

1. Remove the piece of cloth or nylon.
   

Install the 3 clamps.

Connect the antenna connector.

w/ Curtain Shield Airbag:

1. Install 2 new special clips and the clip onto the front pillar garnish.
   

2. Engage the 2 clips and the 2 claws and install the front pillar garnish.
   

w/o Curtain Shield Airbag:

1. Engage the 2 clips and the 2 claws and install the front pillar garnish.
   

w/ Curtain Shield Airbag:

1. Remove the piece of cloth or nylon.
   

Install the 4 clamps.

w/ Curtain Shield Airbag:

1. Install 2 new special clips and the clip onto the front pillar garnish.
   

2. Engage the 2 clips and the 2 claws and install the front pillar garnish.
   

w/o Curtain Shield Airbag:

1. Engage the 2 clips and the 2 claws and install the front pillar garnish.
   

Engage the 2 hooks and 2 clips and install the center pillar upper garnish.

Install the through anchor with the bolt.

Torque:

42 N*m{430 kgf*cm, 31 ft.*lbf}

Engage the 3 claws and install the seat belt anchor cover cap.

Engage the 2 clips and 3claws and install the center pillar lower garnish.

w/ Curtain Shield Airbag:

1. Install a new special clip and the clip onto the roof side inner garnish.
   

2. Engage the 4 clips and the claw and install the roof side inner garnish.
   

w/o Curtain Shield Airbag:

1. Engage the 4 clips and the claw and install the roof side inner garnish.
   

Engage the 2 clips and the 4 claws and install the rear seat side cover.

Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

Paint mark:

Area	Color
RH side	Green
LH side	Red

Engage the 7 claws and install the rear door scuff plate.

Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.

Paint mark:

Area	Color
RH side	Blue
LH side	Pink

Engage the stud bolt and the claw and install the cowl side trim board.

Engage the 4 claws and install the instrument panel under cover.

Engage the 3 claws and install the instrument panel under cover.

Tighten the 2 screws.

Engage the 11 claws and install the front door scuff plate.

w/ Grand Spare Tire:
Install the luggage compartment trim inner pad.

w/o Grand Spare Tire:
Install the luggage compartment trim inner pad.

Install the spare wheel cover.

Install the luggage compartment floor mat.

Insert the 2 hooks into the rear seatback frame hole and install the rear seatback, tightening the 2 bolts in the sequence shown in the illustration.

Torque:

37 N*m{375 kgf*cm, 27 ft.*lbf}

Install the rear seatback cover with the 2 clips.

Pull up the rear seatback.

Install the rear seat outer belt into the rear seat shoulder belt guide.

Install the rear center seat outer belt into the rear center seat shoulder belt guide.

Insert the 2 hooks into the rear seatback frame hole and install the rear seatback, tightening the 2 bolts in the sequence shown in the illustration.

Torque:

37 N*m{375 kgf*cm, 27 ft.*lbf}

Install the rear seatback cover with the 2 clips.

Pull up the rear seatback.

Install the rear seat outer belt into the rear seat shoulder belt guide.

Engage the 3 hooks and install the rear seatback.

Tighten the 3 bolts.

Torque:

7.9 N*m{80 kgf*cm, 70 in.*lbf}

Install the rear seat outer belt into the rear seat shoulder belt guide.

HINT:

Use the same procedure for both sides.

Install the rear center seat outer belt into the rear center seat shoulder belt guide.

for 60/40 Split Seat Type:

1. Install the rear seat cushion cover pad sub-assembly (YARIS_NCP93 RM0000026GB00WX_01_0003.html).
   

for Fixed Seat Type:

1. Install the rear seat cushion cover pad sub-assembly (YARIS_NCP93 RM000001GLY00YX_02_0014.html).
   

Insert the 2 locating pins through the 2 body holes, place the front seat in the most forward position, and then make sure that the inner and outer seat tracks are locked securely.

Using "TORX" socket wrench E10, tighten bolt 1 and then bolt 2 on the rear side.

Torque:

37 N*m{375 kgf*cm, 27 ft.*lbf}

Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are locked securely.

Using "TORX" socket wrench E10, tighten bolt 3 and then bolt 4 on the front side.

Torque:

37 N*m{375 kgf*cm, 27 ft.*lbf}

HINT:

If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.

w/ Front passenger airbag:

1. Connect the airbag connector.
   

2. Connect the buckle switch connector.
   

3. Install the clamp.
   

w/o Front passenger airbag:

1. Connect the buckle switch connector.
   

Push in the lock button of the front seat headrest support and install the front seat headrest.