Dtc U0073 Control Module Communication Bus Off

Brake. Yaris. Ncp93, 131
Brake Control Dynamic Control Systems. Yaris. Ncp93, 131

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

RECONFIRM DTC

REPAIR OR REPLACE HARNESS OR CONNECTOR

RECONFIRM DTC

DTC U0073 Control Module Communication Bus OFF

DTC U0100 Lost Communication with ECM / PCM

DTC U0123 Lost Communication with Yaw Rate Sensor Module

DTC U0124 Lost Communication with Lateral Acceleration Sensor Module

DTC U0126 Lost Communication with Steering Angle Sensor Module


DESCRIPTION

The skid control ECU receives the signals from the ECM, steering angle sensor, and yaw rate and acceleration sensor via the CAN communication system.

DTC Code
DTC Detection Condition
Trouble Area
U0073
When any of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, after the output of data from the skid control ECU is completed, the sending continues for 5 seconds or more.
  2. The condition that bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession. (Sent signals cannot be received.)
  3. When the IG1 terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor continues for 1 second or more.
  4. When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
    1. The condition that a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor occurs more than once within 5 seconds.
CAN communication system
U0100
When either of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more.
  2. When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data cannot be received to the ECM for 2 seconds or more.
CAN communication system
(Skid control ECU to ECM)
U0123
When either of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, data from the yaw rate sensor cannot be received for 1 second or more.
  2. When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
    1. The condition that data from the yaw rate sensor cannot be received occurs once or more within 5 seconds.
CAN communication system
(Skid control ECU to yaw rate and acceleration sensor)
U0124
When either of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.
  2. When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
    1. The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.
CAN communication system
(Skid control ECU to yaw rate and acceleration sensor)
U0126
When either of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.
  2. When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
    1. The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.
CAN communication system
(Skid control ECU to steering angle sensor)

WIRING DIAGRAM


Yaris. Ncp93, 131.Brake Control Dynamic Control Systems.Anti-Lock Brake System (For Sedan). Dtc U0073 Control Module Communication Bus Off


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

  1. Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC (YARIS_NCP93 RM000000XHS09YX.html).

    ABS/VSC/TRAC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    EFI Communication Open
    		EFI communication open detection / ERROR or NORMAL
    		ERROR: Momentary interruption
    NORMAL: Normal
    		-
    Yaw Rate Open
    		Yaw rate sensor open detection / ERROR or NORMAL
    		ERROR: Momentary interruption
    NORMAL: Normal
    		-
    Steering Open
    		Steering sensor open detection / ERROR or NORMAL
    		ERROR: Momentary interruption
    NORMAL: Normal
    		-

    Result
    Result
    		Proceed to
    There are momentary interruptions
    		A
    There are no momentary interruptions
    		B
    There is a constant open circuit
    		C
    HINT:
    Perform the above inspection before removing the sensor and connector.


B
Go to step 3

C
Go to step 4
A


2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

  1. Turn the ignition switch off.

  1. Check if each sensor or ECM connector is securely connected.

    OK:
    Each connector is securely connected.


NG
CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY
OK


3.RECONFIRM DTC

  1. Turn the ignition switch off.

  1. Record the output DTCs (for ABS, VSC, and CAN communication) (YARIS_NCP93 RM000000XHV0BQX.html).

    HINT:
    If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS and VSC) after the CAN communication system returns to normal.

    Result
    Result
    		Proceed to
    DTC output (relating to CAN communication system)
    		A
    DTC output (relating to ABS and/or VSC system)
    		B
    DTC not output
    		C


B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (YARIS_NCP93 RM000000XHU08DX.html)

C
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (YARIS_NCP93 RM000000XHS09YX.html)
A

CHECK CAN COMMUNICATION SYSTEM (YARIS_NCP93 RM000001D3500JX.html)

4.REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and each sensor or ECM (YARIS_NCP93 RM000000XHS09YX.html).

  1. Check that there is no momentary interruption.


NEXT


5.RECONFIRM DTC

  1. Turn the ignition switch off.

  1. Clear the DTC (YARIS_NCP93 RM000000XHV0BQX.html).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.

  1. Check that no CAN communication system DTC is output (YARIS_NCP93 RM000001D3E00OX.html).

  1. If ABS and VSC DTCs are output, record them.

    Result
    Result
    		Proceed to
    DTC output (relating to CAN communication system)
    		A
    DTC output (relating to ABS and/or VSC system)
    		B
    DTC not output
    		C
    HINT:
    The CAN communication system must be normal when repairing each sensor DTC (for ABS and VSC).


B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (YARIS_NCP93 RM000000XHU08DX.html)

C
END
A

CHECK CAN COMMUNICATION SYSTEM (YARIS_NCP93 RM000001D3500JX.html)