Back Window Glass (For Sedan) Removal

for Fixed Seat Type:

1. Remove the rear seat cushion cover pad sub-assembly (YARIS_NCP93 RM000001GM000YX_02_0009.html).
   

for 60/40 Split Seat Type:

1. Remove the rear seat cushion cover pad sub-assembly (YARIS_NCP93 RM0000026GD00WX_01_0003.html).
   

Remove the rear seat outer belt from the rear seat shoulder belt guide.

Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

Pull the rear seatback lock release button and tilt the rear seatback forward.

Using a clip remover, remove the 2 clips and the rear seatback cover.

Remove the 2 bolts, the 2 hooks and the rear seatback.

Remove the rear seat outer belt from the rear seat shoulder belt guide.

Pull the rear seatback lock release button and tilt the rear seatback forward.

Using a clip remover, remove the 2 clips and the rear seatback cover.

Remove the 2 bolts, the 2 hooks and the rear seatback.

Remove the rear seat outer belt from the rear seat shoulder belt guide.

HINT:

Use the same procedure for both sides.

Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

Remove the 3 bolts.

Disengage the 3 hooks and remove the rear seatback.

Remove the luggage compartment floor mat.

Remove the spare wheel cover.

w/ Grand Spare Tire:
Remove the luggage compartment trim inner pad.

w/o Grand Spare Tire:
Remove the luggage compartment trim inner pad.

Disengage the 7 claws and remove the rear door scuff plate.

Remove the rear door opening trim weatherstrip.

Disengage the 2 clips and the 4 claws and remove the rear seat side cover.

w/ Curtain Shield Airbag:

NOTICE:

Replace the special clip with a new one when the roof side inner garnish is removed.

1. Disengage the 4 clips and the claw and remove the roof side inner garnish.
   

w/o Curtain Shield Airbag:

1. Disengage the 4 clips and the claw and remove the roof side inner garnish.
   

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.

Disengage the 2 springs and remove the assist grip.

Disengage the 2 claws.

Disengage the 2 claws.

Disconnect the connector and remove the high mounted stop light assembly.

Using a clip remover, remove the 4 clips.

Disengage the 5 claws and remove the package tray trim panel.

Using a knife, cut off the back window outside moulding, as shown in the illustration.

NOTICE:

Do not damage the vehicle body with the knife.

Remove the back window outside moulding.

HINT:

Make a partial cut in the back window outside moulding. Then pull and remove it by hand.

Apply protective tape to the outer circumference of the back window glass, as shown in the illustration.

From the interior, insert piano wires between the vehicle body and the back window glass, as shown in the illustration.

Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

NOTICE:

1. When separating the back window glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
   
2. To prevent the safety pad from being scratched when removing the back window glass, place a plastic sheet between the piano wire and safety pad.
   

Place matchmarks on the back window glass and vehicle body in the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed unless the back window glass is going to be reused.

Cut through the adhesive by pulling the piano wire around the back window glass.

Disengage the 2 stoppers.

Using suction cups, remove the back window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back window glass.