Windshield Glass (For Hatchback) Installation

Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.

Clean the outer edge of the windshield glass with a non-residue solvent.

NOTICE:

1. Do not touch the windshield glass surface after cleaning it.
   
2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.
   

Using a brush or sponge, coat the application area of the No. 2 windshield glass stoppers with Primer G.

NOTICE:

1. Do not apply too much primer.
   
2. Allow the primer coating to dry for 3 minutes or more.
   
3. Throw away any leftover primer.
   

HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

HINT:

Only 2-piece type No. 2 windshield glass stoppers are supplied. Use the 2-piece type windshield glass stoppers even if a 1-piece type was used.

Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.

HINT:

Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.

Using a brush or sponge, coat the application area of adhesive dam with Primer G.

NOTICE:

1. Do not apply too much primer.
   
2. Allow the primer coating to dry for 3 minutes or more.
   
3. Throw away any leftover primer.
   

HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

Install a new adhesive dam onto the windshield glass, as shown in the illustration.

Clean and shape the contact surface of the vehicle body.

1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
   

   HINT:

   Leave as much adhesive on the vehicle body as possible.

2. Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
   

Position the windshield glass.

1. Using suction cups, place the windshield glass in the correct position.
   

2. Check that the whole contact surface of the windshield glass rim is perfectly even.
   

3. Align the matchmarks on the windshield glass and vehicle body.
   

   NOTICE:

   Check that the windshield glass stoppers are attached to the vehicle body correctly.

4. Remove the windshield glass.
   

Using a brush, coat the installation surface on the vehicle body with Primer M.

NOTICE:

1. Do not coat the adhesive with Primer M.
   
2. Do not apply too much primer.
   
3. Allow the primer coating to dry for 3 minutes or more.
   
4. Do not keep any of the opened Primer M for later use.
   

Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

NOTICE:

1. Do not apply too much primer.
   
2. Allow the primer coating to dry for 3 minutes or more.
   
3. Throw away any leftover primer.
   

HINT:

1. Apply Primer G onto the ceramic notches.
   
2. If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
   

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent

1. Cut off the tip of the cartridge nozzle, as shown in the illustration.
   

   Text in Illustration

   *a	8.0 mm (0.315 in.)
   *b	12.0 mm (0.472 in.)

   HINT:

   After cutting off the tip, use all adhesive within the time limit described in the table below.

   Usage Time Frame:

   Temperature	Usage Time Frame
   35°C (95°F)	15 minutes
   20°C (68°F)	1 hour and 40 minutes
   5°C (41°F)	8 hours

2. Load the sealer gun with a cartridge.
   

Apply adhesive to the windshield glass, as shown in the illustration.

Install the windshield glass.

1. Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
   

   Text in Illustration

   *a

   Mark

   NOTICE:

   1. Check that the windshield glass stoppers are attached to the vehicle body correctly.
      
   2. Check the clearance between the vehicle body and windshield glass.
      

2. Lightly press the front surface of the windshield glass to ensure a close fit.
   

   HINT:

   Press the glass with force of 98 N (10 kgf, 22 lb) or more.





3. If necessary, use a scraper to correct the level or position of adhesive that has been applied.
   

   Text in Illustration

   *1	Windshield
   *2	Dam
   *3	Adhesive

   HINT:

   Apply adhesive onto the windshield glass rim.

Using a brush or sponge, coat the application area of the moulding with Primer G.

NOTICE:

1. Do not apply too much primer.
   
2. Allow the primer coating to dry for 3 minutes or more.
   
3. Throw away any leftover primer.
   

Install a new moulding onto the windshield glass, as shown in the illustration.

Hold the windshield glass using Hold the windshield glass using protective tape until applied adhesive hardens. until applied adhesive hardens.

NOTICE:

Do not drive the vehicle within the time limits described in the table below.

Minimum time:

Temperature	Minimum Time Prior to Driving Vehicle
35°C (95°F)	1 hour and 30 minutes
20°C (68°F)	5 hours
5°C (41°F)	24 hours

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

If water leaks into the cabin, allow the water to dry and add adhesive.

Remove the protective tape.