Can Communication System (For Sedan) Abs And Traction Actuator (Skid Control Ecu) Communication Stop Mode

Power Source Network. Yaris. Ncp93, 131
Networking. Yaris. Ncp93, 131

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CAN BUS LINE FOR CONNECTION (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

CHECK HARNESS AND CONNECTOR (IG1, GND1, GND2)

CAN COMMUNICATION SYSTEM (for Sedan) - ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode


DESCRIPTION


Detection Item
Symptom
Trouble Area
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
  1. "ABS/VSC/TRC" not displayed on "Communication Bus Check" screen of Techstream
  2. Applies to "ABS and Traction Actuator (skid control ECU) Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of ABS and traction actuator (skid control ECU)
  2. ABS and traction actuator (skid control ECU) branch wire or connector
  3. ABS and traction actuator (skid control ECU)
HINT:
For vehicle with VSC only.

WIRING DIAGRAM


Yaris. Ncp93, 131.Networking.Can Communication System (For Sedan).Can Communication System (For Sedan) Abs And Traction Actuator (Skid Control Ecu) Communication Stop Mode


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
  1. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.CHECK CAN BUS LINE FOR CONNECTION (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    Yaris. Ncp93, 131.Networking.Can Communication System (For Sedan).Can Communication System (For Sedan) Abs And Traction Actuator (Skid Control Ecu) Communication Stop Mode

  1. Turn the ignition switch off.

  1. Disconnect the A30 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A30-25 (CANH) - A30-14 (CANL)
    		Ignition switch off
    		54 to 69 Ω
    Text in Illustration
    *1
    		Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK


2.CHECK HARNESS AND CONNECTOR (IG1, GND1, GND2)


    Yaris. Ncp93, 131.Networking.Can Communication System (For Sedan).Can Communication System (For Sedan) Abs And Traction Actuator (Skid Control Ecu) Communication Stop Mode

  1. Disconnect the A30 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    A30-13 (GND2) - Body ground
    		Always
    		Below 1 Ω
    A30-1 (GND1) - Body ground
    		Always
    		Below 1 Ω
    Text in Illustration
    *1
    		Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A30-34 (IG1) - Body ground
    		Ignition switch ON
    		11 to 14 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (YARIS_NCP93 RM000001BXP02FX.html)