Dtc B2273 Ignition 2 Monitor Malfunction

Engine. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
2Az-Fe Starting. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (IG2 RELAY MONITOR [INSIDE])

CHECK SWITCH CONDITION (ENGINE SWITCH)

INSPECT IG2 RELAY

CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)

DTC B2273 Ignition 2 Monitor Malfunction


DESCRIPTION

This DTC is stored when a malfunction occurs in the IG output circuit, which is between the IG2 relay actuation circuit inside the main body ECU and the IG2 relay.

DTC Code
DTC Detection Condition
Trouble Area
B2273
IG2 relay actuation circuit inside the main body ECU or other related circuit is malfunctioning.
  1. Main body ECU
  2. IG2 relay
  3. Harness or connector

WIRING DIAGRAM


Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.2Az-Fe Starting.Starting System (W/ Entry And Start System). Dtc B2273 Ignition 2 Monitor Malfunction


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG2 RELAY MONITOR [INSIDE])

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the display on the intelligent tester.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    IG2 Relay Monitor(Inside)
    		IG2 inner relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    OK:
    When the engine switch is turned on (IG), ON is displayed on the intelligent tester.


NG
Go to step 3
OK


2.CHECK SWITCH CONDITION (ENGINE SWITCH)

  1. Make sure that the electrical key is inside the cabin.

  1. With the shift lever in P, check that the power source mode changes as shown below each time the engine switch is pushed.

    OK:
    off → on (ACC) → on (IG) → off


NG
GO TO POWER SOURCE MODE DOES NOT CHANGE (RAV4_ACA30 RM000000Y7X01OX.html)
OK

USE SIMULATION METHOD TO CHECK (RAV4_ACA30 RM000000UZ306OX.html)

3.INSPECT IG2 RELAY


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.2Az-Fe Starting.Starting System (W/ Entry And Start System). Dtc B2273 Ignition 2 Monitor Malfunction

  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 - 5
    		Battery voltage is applied to terminals 1 and 2
    		Below 1 Ω
    3 - 5
    		Battery voltage is not applied to terminals 1 and 2
    		10 kΩ or higher


NG
REPLACE IG2 RELAY
OK


4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.2Az-Fe Starting.Starting System (W/ Entry And Start System). Dtc B2273 Ignition 2 Monitor Malfunction

  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Disconnect the E19 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    Relay block IG2 relay terminal 1 - E19-5 (IG2D)
    		Always
    		Below 1 Ω
    Relay block IG2 relay terminal 2 - Body ground
    		Always
    		Below 1 Ω
    Relay block IG2 relay terminal 1 or E19-5 (IG2D) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)