2Az-Fe Engine Control System. Dtc P2120 Throttle / Pedal Position Sensor / Switch D Circuit

The APP sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.2Az-Fe Engine Control System.Sfi System.
Dtc
P2120 Throttle / Pedal Position Sensor / Switch D Circuit

DTC No.	DTC Detection Condition	Trouble Area
P2120	VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)	APP sensor ECM
P2122	VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)	APP sensor Open in VCP1 circuit Open or ground short in VPA circuit ECM
P2123	VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)	APP sensor Open in EPA circuit ECM
P2125	VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)	APP sensor ECM
P2127	VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)	APP sensor Open in VCP2 circuit Open or ground short in VPA2 circuit ECM
P2128	Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V	APP sensor Open in EPA2 circuit ECM
P2138	Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less	Short between VPA and VPA2 circuits APP sensor ECM

HINT:

When any of these DTCs are set, check the APP sensor voltage by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Accelerator Position No.1 and Accelerator Position No.2.

Trouble Area	Accelerator Position No.1 When AP Released	Accelerator Position No.2 When AP Released	Accelerator Position No.1 When AP Depressed	Accelerator Position No.2 When AP Depressed
VCP circuit open	0 to 0.2 V	0 to 0.2 V	0 to 0.2 V	0 to 0.2 V
Open or ground short in VPA circuit	0 to 0.2 V	1.2 to 2.0 V	0 to 0.2 V	3.4 to 5.0 V
Open or ground short in VPA2 circuit	0.5 to 1.1 V	0 to 0.2 V	2.6 to 4.5 V	0 to 0.2 V
EPA circuit open	4.5 to 5.0 V	4.5 to 5.0 V	4.5 to 5.0 V	4.5 to 5.0 V
Normal condition	0.5 to 1.1 V	1.2 to 2.0 V	2.6 to 4.5 V	3.4 to 5.0 V

HINT:

Accelerator pedal positions are expressed as voltages.

AP denotes for Accelerator Pedal.

FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuit malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO.1 AND ACCELERATOR POSITION NO.2)

Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the tester ON.

Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No.1 and Accelerator Position No.2.

Read the value displayed on the tester.

Standard voltage:

Accelerator Pedal Operation	Accelerator Position No.1	Accelerator Position No.2
Released → Depressed → Released	0.5 to 4.5 V	1.2 to 5.0 V
Released → Depressed → Released	Difference between Accelerator Position No.1 and Accelerator Position No.2 is greater than 0.02 V	Difference between Accelerator Position No.1 and Accelerator Position No.2 is greater than 0.02 V

Go to step 5

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

Disconnect the A6 Accelerator Pedal Position (APP) sensor connector.

Disconnect the A12 ECM connector.

Measure the resistance.

Standard resistance (Check for open):

Tester Connection	Specified Condition
VPA (A6-6) - VPA (A12-55)	Below 1 Ω
EPA (A6-5) - EPA (A12-59)
VCPA (A6-4) - VCPA (A12-57)
VPA2 (A6-3) - VPA2 (A12-56)
EPA2 (A6-2) - EPA2 (A12-60)
VCP2 (A6-1) - VCP2 (A12-58)

Standard resistance (Check for short):

Tester Connection	Specified Condition
VPA (A6-6) or VPA (A12-55) - Body ground	10 kΩ or higher
EPA (A6-5) or EPA (A12-59) - Body ground
VCPA (A6-4) or VCPA (A12-57) - Body ground
VPA2 (A6-3) or VPA2 (A12-56) - Body ground
EPA2 (A6-2) or EPA2 (A12-60) - Body ground
VCP2 (A6-1) or VCP2 (A12-58) - Body ground

Reconnect the APP sensor connector.

Reconnect the ECM connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

Disconnect the A6 APP sensor connector.

Turn the ignition switch on (IG).

Measure the voltage between the terminals of the A6 APP sensor connector.
Standard voltage:
Tester Connection
Specified Condition
VCPA (A6-4) - EPA (A6-5)
4.5 to 5.5 V
VCP2 (A6-1) - EPA2 (A6-2)

Reconnect the APP sensor connector.

REPLACE ECM

OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)

Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the tester ON.

Clear DTCs (RAV4_ACA30 RM000000PDK0AJX.html).

Start the engine.

Allow the engine to idle for 15 seconds.

Select the following menu items: Powertrain / Engine and ECT / DTC.

Read DTCs.
Result:
Display (DTC Output)
Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138
A
No output
B

SYSTEM OK

REPLACE ECM

Tester Connection	Specified Condition
VCPA (A6-4) - EPA (A6-5)	4.5 to 5.5 V
VCP2 (A6-1) - EPA2 (A6-2)	4.5 to 5.5 V

Display (DTC Output)	Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138	A
No output	B