Dtc 01-Dd Master Reset

Body Electrical. Lexus Is250, Is220D. Gse20 Ale20
Audio Visual. Lexus Is250, Is220D. Gse20 Ale20

DESCRIPTION

INSPECTION PROCEDURE

CHECK RADIO RECEIVER POWER SOURCE CIRCUIT

INSPECT RADIO RECEIVER

IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

REPLACE RADIO RECEIVER

DTC 01-DD Master Reset

DTC 01-E1 Voice Processing Device ON Error


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
01-DD
The device that should be the master has been disconnected after engine start
  1. Radio receiver power source circuit
  1. AVC-LAN circuit between the radio receiver and the component which has stored this code
  1. Radio receiver
  1. Component which has stored this code
01-E1
*1
The AMP device records that the AMP output does not function even while the source device operates
HINT:
*1: Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.
NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  1. The radio receiver is the master unit.
  1. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.

INSPECTION PROCEDURE

NOTICE:
Be sure to read DESCRIPTION before performing the following procedures.
1.CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
Refer to the radio receiver power source circuit (Click here).
If the power source circuit is operating normally, proceed to the next step.

NEXT


2.INSPECT RADIO RECEIVER


    Lexus Is250, Is220D. Gse20 Ale20.Audio Visual.Audio And Visual System. Dtc 01-Dd Master Reset

  1. Disconnect the radio receiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    ATX+ - ATX-
    		Always
    		60 to 80 Ω
    TXM+ - TXM-
    		Always
    		60 to 80 Ω
    TX+ - TX-
    		Always
    		60 to 80 Ω


NG
REPLACE RADIO RECEIVER
OK


3.IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE


  1. Enter the diagnostic mode.


    Lexus Is250, Is220D. Gse20 Ale20.Audio Visual.Audio And Visual System. Dtc 01-Dd Master Reset

  1. Press the preset switch "3" to change to "Detailed Information Mode".

  1. Identify the component which has stored this code.

    Component Table
    Component
    		Physical address
    Gateway ECU
    		1C6
    Stereo component amplifier
    		440
    Integration control & panel assembly
    		1D8
HINT:
  1. "440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.
  1. For details of the DTC display, refer to "DTC CHECK/CLEAR" (Click here).

NEXT


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)
HINT:
For details of the connectors, refer to the "TERMINALS OF ECU" (Click here).


  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the radio receiver and the component which has stored this code.

    1. Disconnect all connectors between the radio receiver and the component which has stored this code.



    2. Check for an open or short in the AVC-LAN circuit between the radio receiver and the component which has stored this code.

      OK:
      There is no open or short circuit.

      Lexus Is250, Is220D. Gse20 Ale20.Audio Visual.Audio And Visual System. Dtc 01-Dd Master Reset



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE RADIO RECEIVER

  1. Replace the radio receiver with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.


NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END