Vehicle Stability Control System (W/ Vdim) Dtc Check / Clear

Brake. Lexus Is250, Is220D. Gse20 Ale20
Brake Control. Lexus Is250, Is220D. Gse20 Ale20
  1. DTC CHECK/CLEAR (INTELLIGENT TESTER)

  1. DTC CHECK/CLEAR (SST CHECK WIRE)

  1. END OF DTC CHECK/CLEAR

Vehicle Stability Control System (W/ Vdim) -- Dtc Check / Clear



DTC CHECK/CLEAR (INTELLIGENT TESTER)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/ Vdim)  Dtc Check / Clear
  1. Check the DTC.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Read the DTCs following the prompts on the tester screen.

  2. Clear the DTC.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Operate the intelligent tester to clear the codes.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

DTC CHECK/CLEAR (SST CHECK WIRE)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/ Vdim)  Dtc Check / Clear
  1. Check the DTC.

    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040
    2. Turn the engine switch on (IG).

    3. Observe the blinking pattern of the ABS warning light and read the multi information display in order to identify the DTC.

      HINT:
      If no code appears, inspect the TC and CG terminal circuit, and ABS and VSC warning light circuits.
      Trouble Area
      See procedure
      TC and CG terminal circuit
      Click here
      ABS warning light circuit
      Click here or Click here
      VSC warning light circuit
      Click here or Click here


    4. As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21 for ABS, and display of the normal system code and trouble code 43 for the VSC on the multi information display.


      Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/ Vdim)  Dtc Check / Clear

    5. The codes are explained in the code table (Click here).

    6. After completing the check, disconnect terminals TC and CG of the DLC3, and turn off the display.
      If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



  2. Clear the DTC.



      Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/ Vdim)  Dtc Check / Clear
    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040
    2. Turn the engine switch on (IG).



    3. Lexus Is250, Is220D. Gse20 Ale20
    4. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    5. Check that the multi information display indicates the normal system code.

    6. Remove the SST from the terminals of the DLC3.

      HINT:
      Clearing the DTCs cannot be performed by removing the battery cable or the ECU-IG LH fuse.

END OF DTC CHECK/CLEAR
  1. Turn the engine switch on (IG).

  2. Check that the ABS warning light goes off within approximately 3 seconds.