Brake. Lexus Is250, Is220D. Gse20 Ale20
Brake Control. Lexus Is250, Is220D. Gse20 Ale20
Vehicle Stability Control System (W/ Vdim) -- Diagnostic Trouble Code Chart |
- If a trouble code is displayed during the DTC check, check the circuit indicated by the DTC. For details of each code, refer to the page for the respective "DTC No." in the DTC chart.
- Inspect the fuse and relay before investigating the trouble areas as shown in the table below.
DTC No. | Detection Item | Trouble Area | See page |
C0200/31 (*1) | Front Speed Sensor RH Circuit | 1. Front speed sensor RH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Skid control ECU | Click here |
C0205/32 (*1) | Front Speed Sensor LH Circuit | 1. Front speed sensor LH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Skid control ECU | Click here |
C0210/33 (*1) | Rear Speed Sensor RH Circuit | 1. Rear speed sensor RH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Skid control ECU | Click here |
C0215/34 (*1) | Rear Speed Sensor LH Circuit | 1. Rear speed sensor LH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Skid control ECU | Click here |
C0226/21 | SFR Solenoid Circuit | 1. SFRR or SFRH circuit 2. Skid control ECU | Click here |
C0236/22 | SFL Solenoid Circuit | 1. SFLR or SFLH circuit 2. Skid control ECU | Click here |
C0246/23 | SRR Solenoid Circuit | 1. SRRR or SRRH circuit 2. Skid control ECU | Click here |
C0256/24 | SRL Solenoid Circuit | 1. SRLR or SRLH circuit 2. Skid control ECU | Click here |
C0273/13 (*1) | Open in ABS Motor Relay Circuit | 1. ABS1 fuse 2. ABS MOTOR2 relay 3. ABS MOTOR2 relay circuit 4. Brake actuator assembly 5. Skid control ECU | Click here |
C0274/14 | Short to B+ in ABS Motor Relay Circuit | 1. ABS1 fuse 2. ABS MOTOR2 relay 3. ABS MOTOR2 relay circuit 4. Brake actuator assembly 5. Skid control ECU | Click here |
C0278/11 | Open in ABS Solenoid Relay Circuit | 1. ABS3 fuse 2. ABS solenoid relay 3. ABS solenoid relay circuit 4. Skid control ECU | Click here |
C0279/12 | Short to B+ in ABS Solenoid Relay Circuit | 1. ABS3 fuse 2. ABS solenoid relay 3. ABS solenoid relay circuit 4. Skid control ECU | Click here |
C1203/59 | ECM Communication Circuit Malfunction | ECM | Click here |
C1225/25 | SM Solenoid Circuit | 1. SM1 or SM2 circuit 2. Skid control ECU | Click here |
C1235/35 | Foreign Object is Attached on Tip of Front Speed Sensor RH | 1. Front speed sensor RH 2. Speed sensor rotor 3. Sensor installation 4. Skid control ECU | Click here |
C1236/36 | Foreign Object is Attached on Tip of Front Speed Sensor LH | 1. Front speed sensor LH 2. Speed sensor rotor 3. Sensor installation 4. Skid control ECU | Click here |
C1238/38 | Foreign Object is Attached on Tip of Rear Speed Sensor RH | 1. Rear speed sensor RH 2. Speed sensor rotor 3. Sensor installation 4. Skid control ECU | Click here |
C1239/39 | Foreign Object is Attached on Tip of Rear Speed Sensor LH | 1. Rear speed sensor LH 2. Speed sensor rotor 3. Sensor installation 4. Skid control ECU | Click here |
C1241/41 | Low Battery Positive Voltage | 1. Battery 2. Charging system 3. Power source circuit 4. Internal power supply circuit of the skid control ECU | Click here |
C1243/43 (*1) | Acceleration Sensor Stuck Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | Click here |
C1244/44 | Open or Short in Acceleration Sensor Circuit | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | Click here |
C1245/45 (*1) | Acceleration Sensor Output Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | Click here |
C1246/46 (*2) | Master Cylinder Pressure Sensor Malfunction | 1. Master cylinder pressure sensor 2. Master cylinder pressure sensor circuit 3. Stop light switch circuit 4. Skid control ECU | Click here |
C1249/49 | Open in Stop Light Switch Circuit | 1. STOP SW fuse 2. Stop light switch 3. Stop light switch circuit 4. Skid control ECU | Click here |
C1251/51 (*1) | Open in Pump Motor Circuit | 1. Brake actuator assembly (GND circuit) 2. Brake actuator assembly (Motor circuit) 3. Skid control ECU | Click here |
C1267/67 | Brake Pedal Load Sensing Switch | 1. Brake pedal load sensing switch 2. Brake pedal load sensing switch circuit | Click here |
C1300/62 | Skid Control ECU Malfunction | Skid control ECU | Click here |
C1336/98 | Zero Point Calibration of Acceleration Sensor Undone | 1. Skid control ECU 2. Yaw rate and acceleration sensor 3. Zero point calibration undone | Click here |
C1361/91 | Short Circuit in ABS Motor Fail Safe Relay Circuit | 1. ABS1 fuse 2. ABS MOTOR1 (fail safe) relay 3. ABS MOTOR1 (fail safe) relay circuit 4. Brake actuator assembly 5. Skid control ECU | Click here |
C1381/97 | Yaw Rate and / or Acceleration Sensor Power Supply Voltage Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor power source circuit | Click here |
U0073/94 | Control Module Communication Bus OFF | CAN communication system | Click here |
U0124/95 | Lost Communication with Lateral Acceleration Sensor Module | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) | Click here |
Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:
- (*1):
- Drive the vehicle at 12 mph (20 km/h) for 30 seconds or more and check that the ABS warning light goes off.
- Clear the DTC.
- (*2):
- Keep the vehicle stationary for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.
- Drive the vehicle at the vehicle speed of 31 mph (50 km/h) and keep depressing the brake pedal strongly for approximately 3 seconds.
- Repeat the above operation 3 times or more and check that the ABS warning light goes off.
- Clear the DTC.
- HINT:
- In some cases, the intelligent tester cannot be used when the ABS warning light remains on.
DTC No. | Detection Item | Trouble Area | See page |
C1201/51 | Engine Control System Malfunction | Engine control system | Click here |
C1210/36 | Zero Point Calibration of Yaw Rate Sensor Undone | 1. Skid control ECU 2. Yaw rate and acceleration sensor 3. Zero point calibration undone | Click here |
C1223/43 | ABS Control System Malfunction | ABS control system | Click here |
C1231/31 | Steering Angle Sensor Circuit Malfunction | 1. Steering angle sensor 2. Steering angle sensor circuit 3. Steering angle sensor power supply 4. Skid control ECU | Click here |
C1234/34 | Yaw Rate Sensor Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | Click here |
C1290/66 | Steering Angle Sensor Zero Point Malfunction | 1. Yaw rate and acceleration sensor zero point calibration incomplete 2. Poor adjustment of the centered position of the steering wheel 3. Poor adjustment of front wheel alignment | Click here |
C1305/21 | Solenoid Identification Circuit | 1. Internal solenoid identification circuit of the brake actuator assembly 2. Skid control ECU | Click here |
U0100/65 | Lost Communication with ECM / PCM | CAN communication system (Skid control ECU to ECM) | Click here |
U0123/62 | Lost Communication with Yaw Rate Sensor Module | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) | Click here |
U0126/63 | Lost Communication with Steering Angle Sensor Module | CAN communication system (Skid control ECU to steering angle sensor) | Click here |
- HINT:
- In some cases, the intelligent tester cannot be used when the VSC warning (multi information display and master caution indicator light) light remains on.
DTC No. | Detection Item | Trouble Area | See page |
C1270/88 | Initialization Incomplete (Test Mode DTC) | 1. ECM 2. CAN communication system (Skid control ECU to ECM) 3. Skid control ECU | Click here |
C1271/71 | Low Output Signal of Front Speed Sensor RH (Test Mode DTC) | 1. Front speed sensor RH 2. Sensor installation 3. Speed sensor rotor | Click here |
C1272/72 | Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | 1. Front speed sensor LH 2. Sensor installation 3. Speed sensor rotor | Click here |
C1273/73 | Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) | 1. Rear speed sensor RH 2. Sensor installation 3. Speed sensor rotor | Click here |
C1274/74 | Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | 1. Rear speed sensor LH 2. Sensor installation 3. Speed sensor rotor | Click here |
C1275/75 | Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) | Speed sensor rotor | Click here |
C1276/76 | Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) | Speed sensor rotor | Click here |
C1277/77 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Speed sensor rotor | Click here |
C1278/78 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Speed sensor rotor | Click here |
C1279/79 | Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) | 1. Yaw rate and acceleration sensor 2. Sensor installation | Click here |
C1281/81 | Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) | 1. Stop light switch 2. Brake pedal load sensing switch 3. Master cylinder pressure sensor | Click here |
DTC No. | Detection Item | Trouble Area | See page |
C0371/71 | Yaw Rate Sensor (Test Mode DTC) | Yaw rate and acceleration sensor | Click here |