Brake Master Cylinder Removal
Brake. Lexus Is250, Is220D. Gse20 Ale20
Brake. Lexus Is250, Is220D. Gse20 Ale20
PRECAUTION
REMOVE COOL AIR INTAKE DUCT SEAL (for 4GR-FSE)
REMOVE COOL AIR INTAKE DUCT SEAL (for 2AD-FHV)
REMOVE ENGINE ROOM SIDE COVER LH (for 4GR-FSE)
REMOVE ENGINE ROOM SIDE COVER LH (for 2AD-FHV)
REMOVE ENGINE ROOM SIDE COVER RH (for 4GR-FSE)
REMOVE ENGINE ROOM COVER SIDE (for 2AD-FHV)
REMOVE FRONT UPPER FENDER PROTECTOR LH (for 4GR-FSE)
REMOVE FRONT UPPER FENDER PROTECTOR LH (for 2AD-FHV)
REMOVE FRONT UPPER FENDER PROTECTOR RH (for 4GR-FSE)
REMOVE FRONT UPPER FENDER PROTECTOR RH (for 2AD-FHV)
REMOVE ROOF DRIP SIDE FINISH MOULDING LH
REMOVE ROOF DRIP SIDE FINISH MOULDING RH
REMOVE FRONT WIPER ARM HEAD CAP (for 4GR-FSE)
REMOVE FRONT WIPER ARM HEAD CAP (for 2AD-FHV)
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (for 4GR-FSE)
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (for 2AD-FHV)
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (for 4GR-FSE)
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (for 2AD-FHV)
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 4GR-FSE)
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 2AD-FHV)
DRAIN BRAKE FLUID
REMOVE NO. 3 ENGINE ROOM RELAY BLOCK
SEPARATE CLUTCH RESERVOIR HOSE (for Manual Transmission)
REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY
Brake Master Cylinder -- Removal |
- HINT:
- (Click here)
2. REMOVE COOL AIR INTAKE DUCT SEAL (for 4GR-FSE) |
Remove the 11 clips and intake duct seal.
3. REMOVE COOL AIR INTAKE DUCT SEAL (for 2AD-FHV) |
Remove the 11 clips and intake duct seal.
4. REMOVE ENGINE ROOM SIDE COVER LH (for 4GR-FSE) |
Remove the 2 clips and side cover.
5. REMOVE ENGINE ROOM SIDE COVER LH (for 2AD-FHV) |
Remove the 4 clips and side cover.
6. REMOVE ENGINE ROOM SIDE COVER RH (for 4GR-FSE) |
Remove the 2 clips and side cover.
7. REMOVE ENGINE ROOM COVER SIDE (for 2AD-FHV) |
Remove the 2 clips and side cover.
8. REMOVE FRONT UPPER FENDER PROTECTOR LH (for 4GR-FSE) |
Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
Disengage the 3 clips and the claw to remove the front upper fender protector LH.
9. REMOVE FRONT UPPER FENDER PROTECTOR LH (for 2AD-FHV) |
Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
Disengage the 3 clips and the claw to remove the front upper fender protector LH.
10. REMOVE FRONT UPPER FENDER PROTECTOR RH (for 4GR-FSE) |
- HINT:
- Use the same procedures for the RH side and the LH side.
11. REMOVE FRONT UPPER FENDER PROTECTOR RH (for 2AD-FHV) |
- HINT:
- Use the same procedures for the RH side and the LH side.
12. REMOVE ROOF DRIP SIDE FINISH MOULDING LH |
Put protective tape around the roof drip side finish moulding.
Using a moulding remover, disengage the 6 clips and remove the roof drip side finish moulding.
- NOTICE:
- Do not remove the clips.
- If the clips are damaged or fall off, replace them with new clips.
13. REMOVE ROOF DRIP SIDE FINISH MOULDING RH |
- HINT:
- Use the same procedures for the RH side and the LH side.
14. REMOVE FRONT WIPER ARM HEAD CAP (for 4GR-FSE) |
Using a screwdriver, remove the front wiper arm head cap.
- HINT:
- Use the same procedures for the RH side and the LH side.
- Tape the screwdriver tip before use.
15. REMOVE FRONT WIPER ARM HEAD CAP (for 2AD-FHV) |
Using a screwdriver, remove the front wiper arm head cap.
- HINT:
- Use the same procedures for the RH side and the LH side.
- Tape the screwdriver tip before use.
16. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (for 4GR-FSE) |
Remove the nut and the front wiper arm and blade assembly LH.
17. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (for 2AD-FHV) |
Remove the nut and the front wiper arm and blade assembly LH.
18. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (for 4GR-FSE) |
Remove the nut and the front wiper arm and blade assembly LH.
19. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (for 2AD-FHV) |
Remove the nut and the front wiper arm and blade assembly RH.
20. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 4GR-FSE) |
Remove the 2 clips.
Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
21. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 2AD-FHV) |
Remove the 2 clips.
Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
- NOTICE:
- If brake fluid leaks onto any painted surface, wash off or remove the brake fluid completely.
23. REMOVE NO. 3 ENGINE ROOM RELAY BLOCK |
Remove the bolt, nut and No. 3 engine room relay block.
- NOTICE:
- Cover the No. 3 engine room relay block with a shop rag or a piece of cloth to prevent brake fluid from getting on it.
24. SEPARATE CLUTCH RESERVOIR HOSE (for Manual Transmission) |
Remove the clip and separate the clutch reservoir hose.
25. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Disengage the clamp and disconnect the warning switch connector.
Using SST, disconnect the 2 brake lines from the brake master cylinder sub-assembly.
- SST
- 09023-00101
Remove the 2 nuts and separate the brake actuator assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
Remove the O-ring from the brake master cylinder sub-assembly.