REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission)
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
REMOVE UPPER CONSOLE PANEL NO. 1 GARNISH (for Automatic Transmission)
REMOVE UPPER CONSOLE PANEL NO. 2 GARNISH (for Automatic Transmission)
REMOVE CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transmission)
REMOVE REAR CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission)
REMOVE FRONT CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission)
Heated Oxygen Sensor (For Sensor 2) -- Removal |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission) |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
 |
| 3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
 |
| 4. REMOVE UPPER CONSOLE PANEL NO. 1 GARNISH (for Automatic Transmission) |
Using a moulding remover, disengage the claw.
 |
Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.
 |
| 5. REMOVE UPPER CONSOLE PANEL NO. 2 GARNISH (for Automatic Transmission) |
Using a moulding remover, disengage the claw.
 |
Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.
 |
| 6. REMOVE CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transmission) |
Disengage the 8 clips.
 |
Disconnect the connectors and remove the console panel sub-assembly.
| 7. REMOVE REAR CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) |
Open the snap.
 |
Disengage the 7 claws and 2 clips, and then remove the rear console panel sub-assembly.
 |
| 8. REMOVE FRONT CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) |
Open the snap.
 |
Pull the front console panel sub-assembly in the direction indicated by the arrow to disengage the 6 clips and remove it.
 |
| 9. REMOVE FRONT ASH RECEPTACLE SUB-ASSEMBLY |
Remove the 2 screws <F>.
 |
Pull the front ash receptacle sub-assembly in the direction indicated by the arrow to disconnect the connectors and remove it.
 |
| 10. REMOVE CONSOLE BOX REGISTER ASSEMBLY |
Remove the rear ash receptacle assembly.
 |
Disengage the 2 claws and 4 clips, and then remove the console box register assembly.
| 11. REMOVE CONSOLE BOX |
Remove the 2 bolts <C>.
 |
Disconnect the 2 connectors.
Disengage the 2 clamps.
Remove the 2 bolts <C>.
 |
Disconnect the connector.
Remove the 2 bolts <C>.
 |
Disengage the 2 claws and 2 clips, and then remove the console box.
 |
| 12. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL |
Disengage the 4 claws and remove the center lower instrument cluster finish panel.
 |
| 13. DISCONNECT CONNECTOR |
Disconnect the oxygen sensor connector.
 |
Disconnect the oxygen sensor connector.
 |
| 14. REMOVE OXYGEN SENSOR |
Disconnect the grommet to the body.
 |
Using the SST, remove the oxygen sensor to the exhaust pipe assembly.
- SST
- 09224-00010
 |