Dtc B1830/57 Short In Curtain Shield Squib Rh Circuit

Restraints. Lexus Gs430, Gs300. Uzs190 Grs190
Supplemental Restraint System. Lexus Gs430, Gs300. Uzs190 Grs190

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

CHECK CONNECTOR

CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB RH CIRCUIT)

CHECK CENTER AIRBAG SENSOR ASSEMBLY

DTC B1830/57 Short in Curtain Shield Squib RH Circuit

DTC B1831/57 Open in Curtain Shield Squib RH Circuit

DTC B1832/57 Short to GND in Curtain Shield Squib RH Circuit

DTC B1833/57 Short to B+ in Curtain Shield Squib RH Circuit


DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the curtain shield squib RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the curtain shield squib RH circuit during primary check.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1831/57
  1. The center airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit for 2 seconds.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1832/57
  1. The center airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1833/57
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


Lexus Gs430, Gs300. Uzs190 Grs190.Supplemental Restraint System.Airbag System. Dtc B1830/57 Short In Curtain Shield Squib Rh Circuit


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
1.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)


    Lexus Gs430, Gs300. Uzs190 Grs190.Supplemental Restraint System.Airbag System. Dtc B1830/57 Short In Curtain Shield Squib Rh Circuit

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the curtain shield airbag assembly RH.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector "C".

    CAUTION:
    Never connect a tester to the curtain shield airbag assembly RH (Curtain shield squib RH) for measurement, as the may lead to a serious injury due to airbag deployment.
    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.
SST
09843-18060

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833 or 57 is not output.
    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833 and 57 may be output at this time, but they are not related to this check.


OK
REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH
NG


2.CHECK CONNECTOR

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector "C".

  1. Check that the floor wire connectors (on the curtain shield airbag assembly RH side) are not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.


NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB RH CIRCUIT)


    Lexus Gs430, Gs300. Uzs190 Grs190.Supplemental Restraint System.Airbag System. Dtc B1830/57 Short In Curtain Shield Squib Rh Circuit

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check the short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Voltage:
      Tester connection
      		Condition
      		Specified condition
      V16-1 (ICR+) -
      Body ground
      		Engine switch on (IG)
      		Below 1 V
      V16-2 (ICR-) -
      Body ground
      		Engine switch on (IG)
      		Below 1 V

  1. Check the open in the circuit.

    1. Turn the engine switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V16-1 (ICR+) -
      V16-2 (ICR-)
      		Always
      		Below 1 Ω

  1. Check the short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V16-1 (ICR+) -
      Body ground
      		Always
      		1 MΩ or higher
      V16-2 (ICR-)
      Body ground
      		Always
      		1 MΩ or higher

  1. Check the short in the circuit.

    1. Release the activation prevention mechanism built into connector "B" (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V16-1 (ICR+) -
      V16-2 (ICR-)
      		Always
      		1 MΩ or higher


NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    Lexus Gs430, Gs300. Uzs190 Grs190.Supplemental Restraint System.Airbag System. Dtc B1830/57 Short In Curtain Shield Squib Rh Circuit

  1. Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833 or 57 is not output.
    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833 and 57 may be output at this time, but they are not related to this check.


NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK