Electronic Controlled Automatic Transmission System Data List / Active Test

Transmission. Lexus Gs430, Gs300. Uzs190 Grs190
A960E Automatic Transmission. Lexus Gs430, Gs300. Uzs190 Grs190

  1. DATA LIST

  1. ACTIVE TEST

Electronic Controlled Automatic Transmission System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG) position.

  5. Turn on the tester.

  6. Select the item "Enter / Power train / ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    		Measurement Item/
    Range (display)
    		Normal Condition
    		Diagnostic Note
    Stop Light Switch
    		Stop light switch Status/
    ON or OFF
    1. Brake Pedal is depressed: ON
    2. Brake Pedal is released: OFF
    		-
    Neutral Position SW Signal
    		PNP switch Status/
    ON or OFF
    		Shift lever position is;
    P and N: ON
    Except P and N: OFF
    		When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).
    Shift SW Status (R Range)
    		PNP switch Status/
    ON or OFF
    		Shift lever position is;
    R: ON
    Except R: OFF
    		↑
    Shift SW Status (D Range)
    		PNP switch Status/
    ON or OFF
    		Shift lever position is;
    D and S: ON
    Except D and S: OFF
    		↑
    Sports Mode Selection SW
    		Sport Mode Select switch Status/
    ON or OFF
    		Shift lever position is;
    S, "+" and "-": ON
    Except S, "+" and "-": OFF
    		-
    Sport Shift Up SW
    		Sport Shift Up switch Status/
    ON or OFF
    1. Press continuously "+" (Up shift): ON
    2. Release "+" (Up shift): OFF
    		-
    Sport Shift Down SW
    		Sport Shift Down switch Status/
    ON or OFF
    1. Press continuously "-" (Down shift): ON
    2. Release "-" (Down shift): OFF
    		-
    Shift Status
    		Actual Gear Position/
    1st, 2nd, 3rd, 4th, 5th or 6th
    		Shift lever position is;
    1. D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. S: 1st, 2nd, 3rd, 4th, 5th or 6th
    		-
    Lock Up Solenoid Status
    		Lock Up Solenoid Status/
    ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    		-
    SLT Solenoid Status
    		Shift Solenoid SLT Status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    		-
    SLU Solenoid Status
    		Shift Solenoid SLU Status/
    ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    		-
    A/T Oil Temperature 1
    		ATF Temp. Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    		If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted.
    SPD (SP2)
    		Output shaft Speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    		Vehicle stopped: 0 km/h (0 mph)
    HINT:
    Equal to vehicle speed
    		-
    SPD (NT)
    		Input Turbine Speed/
    display: 50 r/min
    HINT:
    1. Lock-up ON (After warming up the engine):
      Input Turbine speed (NT) equal to the engine speed.
    2. Lock-up OFF (Idling at N position):
      Input Turbine speed (NT) nearly equal to the engine speed.
    		-
    Pattern Switch (PWR/M)
    		Pattern switch (PWR) Status/
    ON or OFF
    1. Pattern switch (PWR) push: ON
    2. Except pattern switch (PWR) push: OFF
    		-
    Snow Switch Status
    		Pattern switch (ECT SNOW) Status/
    ON or OFF
    1. engine switch ON: OFF
      ↓
    2. Pattern switch (ECT SNOW) Push: ON
      ↓
    3. Pattern switch (ECT SNOW) Push: OFF
    		-
    Kick Down Switch Status
    		Kick Down Switch Status/
    ON or OFF
    1. Accelerator Pedal is depressed all the way down: ON
    2. Accelerator Pedal is released: OFF
    		-


ACTIVE TEST
HINT:
Performing the intelligent tester Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to shorten labor time.
The Data List can be displayed during the Active Test.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG) position.

  5. Turn on the tester.

  6. Select the item "Enter / Power train / ECT / Active Test".

  7. Follow the instructions on the tester and read the Active Test.

    Item
    		Test Details
    		Diagnostic Note
    Control the shift Position
    		[Test Details]
    Operate the shift solenoid valve and set the each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    		Possible to check the operation of the shift solenoid valves.
    Control the Lock Up
    		[Test Details]
    Control the shift solenoid SLU to set the automatic transmission to the lock-up condition.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35 %
    2. Vehicle Speed: 60 km/h (37 mph) or more, and 6th gear
    		Possible to check the SLU operation.
    Control the Line Pressure Up *
    		[Test Details]
    Operate the shift solenoid SLT and raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. IDL: ON
    HINT:
    OFF: Line pressure up (When the active test of "Control the Line Pressure Up" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)
    		-
    *: "Control the Line Pressure Up" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.