Clutch Drum And Input Shaft Assembly Inspection

Hold the coast clutch hub and turn the 1 way clutch assembly.

Check that the 1 way clutch assembly turns freely counterclockwise and locks clockwise.
If there is a problem with the 1 way clutch, replace it.

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

19.51 mm (0.768 in.)

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

21.04 mm (0.828 in.)

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Inspect the pack clearance of the direct clutch.

1. Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across the diameter while blowing air to the oil hole as shown in the illustration, and calculate the average.
   

   HINT:

   Flange moving distance A = 0.26 to 1.14 mm

   Pack clearance = Flange moving distance A - 0.05 mm

   Pack Clearance:

   0.5 to 0.8 mm (0.020 to 0.031 in.)
   

   NOTICE:

   Install a selective flange (t = 3.4 mm) when measuring the moving distance. (shaded area in the illustration.)

2. If the pack clearance is outside the standard, select and install a clutch flange that brings the pack clearance within the standard.
   

   HINT:

   There are 9 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

   Flange thickness:

   No.	Thickness
   2	3.0 mm (0.118 in.)
   3	3.1 mm (0.122 in.)
   4	3.2 mm (0.126 in.)
   5	3.3 mm (0.130 in.)
   6	3.4 mm (0.134 in.)
   7	3.5 mm (0.138 in.)
   8	3.6 mm (0.142 in.)
   9	3.7 mm (0.146 in.)
   A	3.8 mm (0.150 in.)

Inspect the pack clearance of the reverse clutch hub sub-assembly.

1. Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse clutch flange at both ends across the diameter while blowing air (392 kPa, 4 kgf/cm², 57 psi) from the oil hole as shown in the illustration, and calculate the average.
   
   

   
   
   
   

   HINT:

   Piston stroke A = 1.05 to 2.15 mm

   Flange moving distance B = 0.72 to 1.08 mm

   Pack clearance = Piston stroke A - Flange moving distance B - 0.06

   Pack Clearance:

   0.5 to 0.8 mm (0.020 to 0.031 in.)
   

   NOTICE:

   Install a selective flange (t = 3.3 mm) when measuring the moving distance. (shaded area in the illustration)

2. If the pack clearance is outside the standard, select and install a clutch flange that brings the pack clearance within the standard.
   

   HINT:

   There are 11 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

   Flange thickness:

   No.	Thickness
   0	2.8 mm (0.110 in.)
   1	2.9 mm (0.114 in.)
   2	3.0 mm (0.118 in.)
   3	3.1 mm (0.122 in.)
   4	3.2 mm (0.126 in.)
   5	3.3 mm (0.130 in.)
   6	3.4 mm (0.134 in.)
   7	3.5 mm (0.138 in.)
   8	3.6 mm (0.142 in.)
   9	3.7 mm (0.146 in.)
   A	3.8 mm (0.150 in.)

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

24.64 mm (0.9701 in.)

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Inspect the pack clearance of the coast clutch hub sub-assembly.

1. Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across the diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
   

   HINT:

   Flange moving distance A = 0.38 to 1.48 mm (0.01496 to 0.0583 in.)

   Pack clearance = Flange moving distance A - 0.02 mm (0.0008 in.)

   Pack Clearance:

   0.3 to 0.6 mm (0.012 to 0.024 in.)
   

   NOTICE:

   Install a selective flange (t = 3.0 mm) when measuring the moving distance. (shaded area in the illustration.)

2. If the pack clearance is outside the standard, select and install a clutch flange that brings the pack clearance within the standard.
   

   HINT:

   There are 10 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

   Flange thickness:

   No.	Thickness
   0	3.0 mm (0.118 in.)
   1	3.1 mm (0.122 in.)
   2	3.2 mm (0.126 in.)
   3	3.3 mm (0.130 in.)
   4	3.4 mm (0.134 in.)
   5	3.5 mm (0.138 in.)
   6	3.6 mm (0.142 in.)
   7	3.7 mm (0.146 in.)
   8	3.8 mm (0.150 in.)
   9	3.9 mm (0.154 in.)

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Inspect the pack clearance of the forward clutch.

1. Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across the diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
   

   HINT:

   Flange moving distance A = 0.36 to 1.50 mm

   Pack clearance = Flange moving distance A - 0.11 mm

   Pack Clearance:

   0.56 to 0.86 mm (0.0220 to 0.0339 in.)
   

   NOTICE:

   Install a selective flange (t = 3.4 mm) when measuring the moving distance. (shaded area in the illustration.)

2. If the pack clearance is outside the standard, select and install a clutch flange that brings the pack clearance within the standard.
   

   HINT:

   There are 11 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

   Flange thickness:

   No.	Thickness
   0	3.0 mm (0.118 in.)
   1	3.1 mm (0.122 in.)
   2	3.2 mm (0.126 in.)
   3	3.3 mm (0.130 in.)
   4	3.4 mm (0.134 in.)
   5	3.5 mm (0.138 in.)
   6	3.6 mm (0.142 in.)
   7	3.7 mm (0.146 in.)
   8	3.8 mm (0.150 in.)
   9	3.9 mm (0.154 in.)
   A	4.0 mm (0.158 in.)

Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

Standard inside diameter:

26.037 to 26.062 mm (1.0251 to 1.0261 in.)

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Using a dial indicator, measure the inside diameter of the reverse clutch hub bushing.

Standard inside diameter:

35.812 to 35.837 mm (1.4099 to 1.4109 in.)