Dtc P2048 Reductant Injector Circuit Low (Bank 1 Unit 1)
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
INSPECT UREA INJECTOR SET
CHECK HARNESS AND CONNECTOR (UREA INJECTOR SET - UREA PUMP CONTROL ECU)
CLEAR DTC
CHECK DTC OUTPUT
REPLACE UREA PUMP CONTROL ECU
CLEAR DTC
CHECK DTC OUTPUT
REPAIR OR REPLACE HARNESS AND CONNECTOR
REPLACE UREA INJECTOR SET
DTC P2048 Reductant Injector Circuit Low (Bank 1 Unit 1) |
DTC P2049 Reductant Injector Circuit High (Bank 1 Unit 1) |
DESCRIPTION
The urea injector opens the needle valve and injects urea solution according to operation signals sent by the urea pump control ECU. P2048DTC Detection Drive Pattern
| DTC Detection Condition
| Trouble Area
|
Reductant Injection Valve (Active Test)
| When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more. (1 trip detection logic)
| - Open or short in urea injector set circuit
- Urea injector set
- Urea pump control ECU
|
P2049DTC Detection Drive Pattern
| DTC Detection Condition
| Trouble Area
|
Reductant Injection Valve (Active Test)
| When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more. (1 trip detection logic)
| - Open or short in urea injector set circuit
- Urea injector set
- Urea pump control ECU
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.INSPECT UREA INJECTOR SET |
Inspect the urea injector set (LandCruiser RM000005UKT000X.html).
2.CHECK HARNESS AND CONNECTOR (UREA INJECTOR SET - UREA PUMP CONTROL ECU) |
Disconnect the urea injector set connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
C184-2 - s3-8 (UIV+)
| Always
| Below 1 Ω
|
C184-1 - s3-7 (UIV-)
| Always
| Below 1 Ω
|
C184-2 or s3-8 (UIV+) - Body ground and other terminals
| Always
| 10 kΩ or higher
|
C184-1 or s3-7 (UIV-) - Body ground and other terminals
| Always
| 10 kΩ or higher
|
Text in Illustration*a
| Front view of wire harness connector (to Urea Injector Set)
| *b
| Front view of wire harness connector (to Urea Pump Control ECU)
|
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (LandCruiser RM000000PDK1E5X.html).
Turn the engine switch off for 30 seconds or more.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
- Result:
Result
| Proceed to
|
DTC P2048 or P2049 is output
| A
|
DTCs is not output
| B
|
5.REPLACE UREA PUMP CONTROL ECU |
Replace the urea pump control ECU (LandCruiser RM000005UL6000X.html).
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (LandCruiser RM000000PDK1E5X.html).
Turn the engine switch off for 30 seconds or more.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
8.REPAIR OR REPLACE HARNESS AND CONNECTOR |
Repair or replace the harness or connector.
9.REPLACE UREA INJECTOR SET |
Replace the urea injector set (LandCruiser RM000005UL6000X.html).