Ecd System (W/ Urea Scr System) Fuel Injection System


INSPECTION PROCEDURE

CHECK INJECTOR COMPENSATION CODE

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)

READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

CHECK CYLINDER COMPRESSION PRESSURE

PERFORM PILOT QUANTITY LEARNING

READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

READ VALUE USING GTS (INJECTION VOLUME)

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

REPLACE FUEL FILTER ELEMENT ASSEMBLY

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

CHECK AND REPLACE ENGINE ASSEMBLY

PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

INSPECT CLOGGED FUEL PIPE

REPAIR OR REPLACE CLOGGED FUEL LINE

REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

BLEED AIR FROM FUEL SYSTEM

READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

REPLACE FUEL SUPPLY PUMP ASSEMBLY

BLEED AIR FROM FUEL SYSTEM

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

ECD SYSTEM (w/ Urea SCR System) - Fuel Injection System


INSPECTION PROCEDURE

NOTICE:
After replacing an injector assembly, the ECM needs registration (LandCruiser RM0000012XK0AUX.html).
1.CHECK INJECTOR COMPENSATION CODE

  1. Check the injector compensation code (LandCruiser RM0000012XK0AUX_02_0006.html).

    Result
    Result
    		Proceed to
    Except below
    		A
    Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM
    		B


B
Go to step 3
A


2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

  1. Register the injector compensation codes (LandCruiser RM0000012XK0AUX_02_0003.html).

  1. Perform the injector pilot quantity learning (LandCruiser RM0000012XK0AUX_02_0009.html).


NEXT


3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)

  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common rail (All).

  1. Take a snapshot of the following Data List items.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.

NEXT


4.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

  1. Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.

    Result
    Result
    		Proceed to
    Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st
    		A
    Injection Volume is 10 mm3/st or less at 4000 rpm
    		B
    Except above
    		C
    HINT:
    1. When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
    2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.


B
Go to step 11

C
Go to step 10
A


5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    Result
    Result
    		Proceed to
    Except below
    		A
    The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other.
    		B
    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.


B
Go to step 7
A


6.CHECK CYLINDER COMPRESSION PRESSURE

  1. Check the cylinder compression pressure (LandCruiser RM000005UTQ000X_02_0009.html).

    HINT:
    When compression is low, there may be cracks in the piston or the injector assembly may be installed improperly.


NG
Go to step 15
OK


7.PERFORM PILOT QUANTITY LEARNING

  1. Perform the injector pilot quantity learning (LandCruiser RM0000012XK0AUX_02_0009.html).


NEXT


8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

  1. Read the values.

    Standard:

    GTS Display
    		Engine Condition*
    		Normal Value
    Injection Feedback Val #1
    Injection Feedback Val #2
    Injection Feedback Val #3
    Injection Feedback Val #4
    		Idling
    		 -3.0 mm3/st to 3.0 mm3/st
    HINT:
    *: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or more and the engine should be idled for 1 minute or more.

    Result
    Result
    		Proceed to
    Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st
    		A
    Except above
    		B
    HINT:
    1. When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
    2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.


B
Go to step 16
A


9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

  1. Replace the injector assembly of the malfunctioning cylinder (LandCruiser RM000005UHS000X.html).

    NOTICE:
    1. When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
    2. Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.


NEXT
Go to step 12

10.READ VALUE USING GTS (INJECTION VOLUME)

  1. Check Injection Volume in the snapshot taken in procedure 3 when the engine was idling.

    Result
    Result
    		Proceed to
    Injection Volume while idling after engine warm up is 16 mm3/st or more
    		A
    Except above
    		B
    HINT:
    1. Check that PM forced regeneration is not being performed.
    2. The idling speed during PM forced regeneration is 800 to 1000 rpm (with the shift lever in neutral).


B
Go to step 16
A


11.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

  1. Replace the injector assemblies of all cylinders (LandCruiser RM000005UHS000X.html).

    NOTICE:
    1. When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
    2. Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.

NEXT


12.REPLACE FUEL FILTER ELEMENT ASSEMBLY

  1. Replace the fuel filter element assembly (LandCruiser RM0000045HW008X.html).


NEXT


13.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).


NEXT


14.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

  1. Register the injector compensation codes (LandCruiser RM0000012XK0AUX_02_0003.html).

  1. Perform the injector pilot quantity learning (LandCruiser RM0000012XK0AUX_02_0009.html).



NEXT
Go to step 16

15.CHECK AND REPLACE ENGINE ASSEMBLY

  1. Check and replace the engine assembly.


NEXT


16.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

  1. Start the engine.

  1. Take a snapshot with the GTS during the Active Test.



  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.1Gd-Ftv Engine Control.Ecd System.Ecd System (W/ Urea Scr System) Fuel Injection System

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).

    Result
    Result
    		Proceed to
    NG
    		A
    OK*
    		B
    NOTICE:
    *: Even when the results of the Active Test are normal, take a snapshot of vehicle data when the vehicle is accelerating. If "Common Rail Pressure" does not follow "Target Common Rail Pressure", proceed to step 17.
    If "Common Rail Pressure" does not follow "Target Common Rail Pressure", the fuel filter may be clogged.
    HINT:
    1. "Target Common Rail Pressure" means target fuel pressure controlled by the ECM.
    2. "Common Rail Pressure" means actual fuel pressure in common rail assembly.
    3. If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Malfunctioning" in the illustration.
    4. The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.


B
Go to step 22
A


17.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check (LandCruiser RM000002SY803FX_01_0005.html).

  1. Select "Always Closed Check".

  1. Press "Next".

  1. Read the Value of fuel pressure values.

    OK:
    Fuel pressure is properly maintained.
    HINT:
    1. If the fuel pressure cannot be maintained, the pressure discharge valve may not have a tight seal.
    2. If the fuel pressure is being properly maintained, there are no problems with the sealing properties of the high-pressure fuel system. Therefore, an insufficient supply of fuel due to the fuel filter being clogged, or squashed or blocked low-pressure fuel pipes or hoses may be causing the reduction in common rail pressure.


NG
Go to step 20
OK


18.INSPECT CLOGGED FUEL PIPE

  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail (All).

  1. With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.



  1. Check the Target Common Rail Pressure and Common Rail Pressure value.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.1Gd-Ftv Engine Control.Ecd System.Ecd System (W/ Urea Scr System) Fuel Injection System


    Result
    Result
    		Proceed to
    While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1
    		A
    "Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
    Except above
    		B
    NOTICE:
    1. *1: The cause may be a squashed or blocked fuel pipe or hose.
    2. *2: The cause may be a clogged fuel filter element assembly.


B
Go to step 23
A


19.REPAIR OR REPLACE CLOGGED FUEL LINE

  1. Repair or replace the clogged (including frozen fuel) fuel pipe.

  1. Replace the fuel filter element assembly.

    HINT:
    If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.


NEXT
Go to step 21

20.REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

  1. Replace the common rail assembly (LandCruiser RM000005UI0000X.html).


NEXT


21.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).


NEXT


22.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

  1. Check Common Rail Pressure and Target Common Rail Pressure in the snapshot taken in procedure 3 when the engine was idling.

    Result
    Result
    		Proceed to
    Difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more
    		B
    Except above
    		A


B
Go to step 23
A

END

23.REPLACE FUEL SUPPLY PUMP ASSEMBLY

  1. Replace the fuel supply pump assembly (LandCruiser RM000005UHX000X.html).


NEXT


24.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).


NEXT


25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END