Roof Headlining (For 3 Door) Removal

for LH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM0000046ZI006X.html).

for RH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM0000046ZN006X.html).

Put protective tape around the door scuff plate.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

HINT:

Tape the screwdriver tip before use.

Remove the clip.

Detach the clip and claw and remove the cowl side trim board.

Remove the front door opening trim weatherstrip.

Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts.

Detach the 2 claws and remove the No. 1 assist grip.

Detach the 3 guides and remove the front pillar garnish.

w/ Curtain Shield Airbag:
Protect the curtain shield airbag assembly.

1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
   

   NOTICE:

   Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

   Text in Illustration

   *1	Curtain Shield Airbag Assembly
   *2	Adhesive Tape
   *3	Protective Cover

Remove the tonneau cover.

Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

HINT:

Tape the screwdriver tip before use.

Remove the 5 screws.

Detach the 6 claws and remove the rear floor mat rear support plate.

Detach the 2 claws and 2 guides and remove the quarter trim cover hole.

Remove the rear floor carpet.

Remove the luggage compartment trim hook by turning it clockwise.

Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

HINT:

Tape the screwdriver tip before use.

Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

HINT:

Tape the screwdriver tip before use.

Put protective tape around the quarter trim pocket tray.

Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

HINT:

Tape the screwdriver tip before use.

Detach the 3 claws and remove the outer lap belt anchor cover.

Remove the bolt and disconnect the front seat outer belt floor anchor.

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

Remove the 3 bolts and 2 screws.

Detach the 9 claws and 12 clips and remove the deck trim side panel.

Remove the bolt and disconnect the front seat outer belt floor anchor.

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

Remove the 3 bolts and 2 screws.

Detach the 9 claws and 12 clips.

Disconnect the connector and remove the deck trim side panel.

Move the front shoulder belt anchor adjuster to the lowest position.

Remove the bolt.

Detach the 2 clips and 2 guides.

Pass the front seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

Detach the 7 clips.

Detach the 4 claws and 2 guides, pass the rear No. 1 seat belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.

Detach the 2 clips and remove the assist grip.

Remove the 2 clips from the vehicle body.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.

Detach the 2 clips and remove the assist grip.

Remove the 2 clips from the vehicle body.

Detach the 4 claws and remove the visor bracket cover.

Remove the 2 screws and visor.

Turn the visor holder approximately 45° and pull it out as shown in the illustration.

Detach the 2 claws and remove the visor holder.

Detach the 4 clips.

Disconnect the connector and remove the map light.

Detach the 2 claws and remove the rain sensor cover.

Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

Detach the 2 claws and remove the inner rear view mirror stay holder cover.

Remove the No. 1 room light assembly (LandCruiser RM000003MUN052X.html).

Remove the No. 2 room light assembly (LandCruiser RM000003MUN053X.html).

Detach the 5 clips.

Cut off the 5 clips and remove the roof side rail garnish LH.

Remove the 5 clips from the vehicle body.

w/ EC Mirror:
Disconnect the inner mirror connector.

w/ Rain Sensor:
Disconnect the rain sensor connector.

w/ Sliding Roof:
Disconnect the drive gear connector.

w/ Digital Audio Broadcasting Antenna:
Disconnect the connector and detach the wire harness clamp.

Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

Remove the bolt.

Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

Disconnect the connector and detach the 3 clamps from the rear pillar LH.

Disconnect the connector and detach the 4 clamps from the rear pillar RH.

w/o Sliding Roof:

1. Detach the 2 clips.
   

w/ Sliding Roof:

1. Detach the 2 clips, 2 guides and 8 fasteners.
   

   Text in Illustration

   *1	Guide
   *2	Fastener

Remove the roof headlining from the back door as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when removing it.

Detach the 4 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.

Remove the clip.

Detach the 4 claws and remove the rear side rail spacer.

Detach the 4 claws and remove the deck side trim cup holder.

Detach the claw and guide and remove the rear seat shoulder belt hanger.

Detach the 2 claws and remove the quarter trim cover.

Detach the 7 claws and 3 guides and remove the quarter trim jack cover.

Turn the 2 knobs and release the lock.

Detach the 7 claws and 3 guides and remove the deck side trim cover.