REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
Front Seat Assembly (For Manual Seat) -- Disassembly |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
 |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective Tape
| 2. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side) |
 |
Remove the screw and handle.
| 3. REMOVE FRONT SEAT CUSHION SHIELD LH |
Remove the screw.
 |
Using a moulding remover, detach the 4 claws and clip, and then remove the cushion shield.
for Driver Side:
Detach the 5 wire harness clamps and disconnect the 2 connectors.
 |
| 4. REMOVE LUMBAR SWITCH ASSEMBLY (for Driver Side) |
 |
Remove the 2 screws and switch.
| 5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH |
 |
Using a moulding remover, detach the 3 claws and remove the cushion shield.
| 6. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side) |
 |
Using a moulding remover, detach the 4 claws and remove the cushion shield.
| 7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
for Driver Side:
(LandCruiser RM000003RQO025X_01_0006.html)
for Front Passenger Side:
(LandCruiser RM000003RQO025X_01_0001.html)
| 8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
Remove the rubber band from the seat cushion spring.
 |
for Driver Side:
Detach the clamp and disconnect the No. 2 seat wire.
 |
w/ Seat Heater System:
Disconnect the seat heater connector and detach the wire harness clamp.
 |
for Clip Type:
Using a clip remover, remove the 2 clips.
 |
for Hook Type:
Detach the 2 hooks.
 |
w/ Front Seat Side Airbag:
Detach the claw and disconnect the airbag connector.
Detach the 3 airbag wire harness clamps.
Detach the fastening tape and open the cover.
Text in Illustration *1 Fastening Tape Disconnect the airbag wire harness.
 |
Remove the 4 bolts and seatback assembly.
 |
| 9. REMOVE CAP |
 |
Remove the 2 caps.
| 10. REMOVE FRONT SEAT LEG COVER LH |
 |
Detach the 2 claws.
Move the cover in the direction of the arrow to remove it.
| 11. REMOVE SEAT CUSHION COVER WITH PAD |
w/ Seat Heater System:
Disconnect the seat heater connector and detach the 3 wire harness clamps.
 |
Detach the hooks.
for Front Passenger Side:
Detach the claw and disconnect the connector.
 |
Remove the seat cushion cover with pad.
| 12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
Type A:
Remove the hog rings and disconnect the straps.
 |
Type B:
Cut off the tack pins and disconnect the straps.
Text in Illustration *1 Tack Pin
 |
Remove the hog rings and seat cushion cover from the seat cushion pad.
 |
| 13. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
 |
Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.
Text in Illustration *1 Tack Pin
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
Detach the claw and guide, and then remove the cover.
| 15. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
 |
Remove the screw.
Detach the hook and clip, and then remove the cushion shield.
| 16. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
Remove the screw.
Detach the hook and clip, and then remove the cushion shield.
| 17. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH |
 |
Remove the screw.
Move the protector in the direction of the arrow to detach the hook and remove the protector.
| 18. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH |
- HINT:
- Use the same procedure described for the LH side.
| 19. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
 |
Disconnect the connector.
Detach the 2 clamps and remove the seat heater control.
| 20. REMOVE FRONT SEAT WIRE LH |
Remove the seat wire.
| 21. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
Detach the guide.
Move the cover in the direction of the arrow to remove it.
| 22. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 23. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
Remove the 3 hog rings.
 |
Open the 2 fasteners, and then open the seatback cover.
Text in Illustration *A for Cloth Seat *B for Leather Seat
w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
Disconnect the seatback cover bracket from the seatback pad.
 |
Using a screwdriver, detach the 4 claws and remove the 2 headrest supports.
 |
Remove the hog rings and seatback cover.
- HINT:
- The number of hog rings differs according to seat type.
Text in Illustration *A for Type A *B for Type B
| 24. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
 |
Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
Text in Illustration *1 Tack Pin
| 25. REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
Remove the seatback pad.
| 26. REMOVE NO. 2 SEAT WIRE (for Driver Side) |
 |
Disconnect the connector.
Detach the 2 clamps and remove the seat wire.
| 27. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) |
- CAUTION:
- When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.
- HINT:
- Use the same procedure for the RH and LH sides.
Detach the 2 clamps.
 |
Remove the 2 nuts and front seat side airbag assembly.
- CAUTION:
- The nuts must not be reused.
- Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.
 |