Side Airbag Sensor Installation


  1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

  2. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

  3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  4. INSTALL ASSIST GRIP COVER LH

  5. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

  6. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  8. CHECK SRS WARNING LIGHT

Side Airbag Sensor -- Installation


HINT:
  1. Use the same procedure for LHD and RHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH side and LH side.
  4. The procedure listed below is for the LH side.


1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Install the side airbag sensor with the bolt.

    Torque:
    9.0 N*m{92 kgf*cm, 80 in.*lbf}
    NOTICE:
    1. If the side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the side airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that the side airbag sensor is not loose.

  1. Connect the connector.



2. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Install the front door inner glass weatherstrip.



3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

  1. Connect 2 connectors.

  1. w/ Seat Position Memory System:

    1. Connect the connectors.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the front door trim board sub-assembly by attaching the 4 claws of the front door inner glass weatherstrip as shown in the illustration.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 12 clips and front door trim board retainer to install the front door trim board sub-assembly.

  1. Install the 3 screws.



4. INSTALL ASSIST GRIP COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 8 claws to install the assist grip cover.



5. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 3 claws to install the inside handle bezel.



6. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. Attach the 2 claws to install the front door lower frame bracket garnish.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


8. CHECK SRS WARNING LIGHT

  1. Check the SRS warning light (LandCruiser RM000000XFD0N3X.html).