Rear Door Window Frame Moulding Removal


  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  4. REMOVE ASSIST GRIP COVER LH

  5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  7. REMOVE REAR DOOR SERVICE HOLE COVER LH

  8. REMOVE REAR DOOR GLASS RUN LH

  9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  12. REMOVE REAR DOOR BELT MOULDING LH

  13. REMOVE REAR DOOR WEATHERSTRIP LH

  14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

Rear Door Window Frame Moulding -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When removing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.
Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Window Frame Moulding
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body or window frame moulding excessively.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.



4. REMOVE ASSIST GRIP COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using moulding remover A, detach the 8 claws and remove the assist grip cover.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 3 screws.

  1. Using a clip remover, detach the 9 clips.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Rear Door Window Frame Moulding Removal

  1. Disconnect each connector.

    Text in Illustration
    *A
    		for 14 Speakers
    *B
    		for 9 Speakers


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a screwdriver, detach the claw and remove the clamp.



6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.



7. REMOVE REAR DOOR SERVICE HOLE COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the connector.

  1. Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


8. REMOVE REAR DOOR GLASS RUN LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door glass run.



9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Rear Door Window Frame Moulding Removal

  1. Loosen the temporary bolt.

    Text in Illustration
    *1
    		Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window division bar sub-assembly.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.



10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.



11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Rear Door Window Frame Moulding Removal

  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


12. REMOVE REAR DOOR BELT MOULDING LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Rear Door Window Frame Moulding Removal

  1. Detach the 7 claws and remove the rear door belt moulding.

    Text in Illustration
    *1
    		Protective Tape


13. REMOVE REAR DOOR WEATHERSTRIP LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the clip and remove the upper part of the rear door weatherstrip so that the moulding can be removed.



14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the door window frame moulding clip.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Rear Door Window Frame Moulding Removal

  1. Put protective tape around the rear door front window frame moulding.

  1. Using a moulding remover, detach the clip and remove the double-sided tape to remove the rear door front window frame moulding.

    Text in Illustration
    *1
    		Protective Tape
    *2
    		Double-sided Tape
    *3
    		Moulding Remover