Dtc U0208 Lost Communication With Seat Control Module A


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE)

CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - BATTERY AND BODY GROUND)

DTC U0208 Lost Communication with "Seat Control Module A"


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
U0208
There is no communication from the front power seat switch RH.
  1. Power source or inside front power seat switch RH
  2. Front power seat switch RH CAN branch wire or connector
  3. Front power seat switch RH
  1. For vehicles with a seat position memory.

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System. Dtc U0208 Lost Communication With Seat Control Module A


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).

NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System. Dtc U0208 Lost Communication With Seat Control Module A

  1. Disconnect the a5 front power seat switch RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    a5-8 (CANP) - a5-7 (CANN)
    		Engine switch off
    		54 to 69 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to Front Power Seat Switch RH)


NG
REPAIR OR REPLACE FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - BATTERY AND BODY GROUND)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System. Dtc U0208 Lost Communication With Seat Control Module A

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).

  1. Disconnect the a4 front power seat switch RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    a4-2 (GND) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    a4-7 (+B) - Body ground
    		Always
    		11 to 14 V
    a5-12 (SYSB) - Body ground
    		Always
    		11 to 14 V
Text in Illustration
*a
Rear view of wire harness connector
(to Front Power Seat Switch RH)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH RH (LandCruiser RM000004673017X.html)