Navigation System (For Navigation Receiver Type) Microphone Circuit Between Microphone And Navigation Receiver Assembly


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK NAVIGATION RECEIVER ASSEMBLY

CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY)

CHECK TELEPHONE MICROPHONE ASSEMBLY

NAVIGATION SYSTEM (for Navigation Receiver Type) - Microphone Circuit between Microphone and Navigation Receiver Assembly


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.
It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Navigation Multi Info Display.Navigation System (For Radio And Display Type).Navigation System (For Navigation Receiver Type) Microphone Circuit Between Microphone And Navigation Receiver Assembly


INSPECTION PROCEDURE

HINT:
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
1.CHECK NAVIGATION RECEIVER ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Navigation Multi Info Display.Navigation System (For Radio And Display Type).Navigation System (For Navigation Receiver Type) Microphone Circuit Between Microphone And Navigation Receiver Assembly

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    H56-19 (MIN-) - Body ground
    		Always
    		Below 1 Ω
    H56-18 (SGND) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    H56-4 (MACC) - Body ground
    		Engine switch on (ACC)
    		4.75 to 5.25 V
    Text in Illustration
    *a
    		Component with harness connected
    (Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (LandCruiser RM000003B6H02GX.html)
OK


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY)

  1. Disconnect the H56 navigation receiver assembly connector.

  1. Disconnect the W7 roof console box assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    H56-4 (MACC) - W7-11 (MACC)
    		Always
    		Below 1 Ω
    H56-5 (MIN+) - W7-12 (MCO+)
    		Always
    		Below 1 Ω
    H56-19 (MIN-) - W7-13 (MCO-)
    		Always
    		Below 1 Ω
    H56-6 (SNS2) - W7-14 (SNS2)
    		Always
    		Below 1 Ω
    H56-4 (MACC) - Body ground
    		Always
    		10 kΩ or higher
    H56-5 (MIN+) - Body ground
    		Always
    		10 kΩ or higher
    H56-19 (MIN-) - Body ground
    		Always
    		10 kΩ or higher
    H56-18 (SGND) - Body ground
    		Always
    		10 kΩ or higher
    H56-6 (SNS2) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK TELEPHONE MICROPHONE ASSEMBLY

  1. Replace the telephone microphone assembly with a known good one (LandCruiser RM000002LJJ04XX.html).

  1. Check if the same problem occurs again.

    OK:
    Malfunction disappears.


NG
REPLACE MAP LIGHT ASSEMBLY (LandCruiser RM000003YO9019X.html)
OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)