Fuel System Precaution

Before starting work on the fuel system, including inspections and repairs, disconnect the cable from the negative (-) battery terminal.

Do not smoke or work near fire when performing work on the fuel system.

Keep gasoline away from rubber or leather parts.

Remove the circuit opening relay from the engine room relay block.

Start the engine. After the engine stops, turn the engine switch off.

HINT:

DTC P0171 (system to lean) may be stored.

Check that the engine does not start.

Remove the fuel tank cap and let the air out of the fuel tank.

Disconnect the cable from the negative battery (-) terminal.

NOTICE:

1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
   
2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).
   

Reinstall the circuit opening relay.

When disconnecting a high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.

1. Disconnect the fuel pump tube.
   

2. Drain any fuel remaining inside the fuel pump tube.
   

3. To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.
   

4. Put a container under the connection.
   

Observe these precautions when removing and installing the injectors.

1. Never reuse the O-ring.
   

2. When installing a new O-ring to the injector, do not damage it.
   

3. Coat new O-rings with spindle oil or gasoline before installing. Do not use engine oil, gear oil or brake oil.
   

Install the injector to the delivery pipe and lower intake manifold as shown in the illustration.

NOTICE:

Before installing the injector, be sure to apply spindle oil or gasoline to the place where the delivery pipe or cylinder head contacts the O-ring of the injector.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

1. Fuel Hose Connector Cover Type:
   Detach the lock claw by lifting up the cover as shown in the illustration.
   

   Text in Illustration

   *1	Fuel Hose Connector Cover

2. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.
   





3. If the connector and the pipe are stuck, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.
   

   Text in Illustration

   *1	Retainer
   	Pinch
   	Pull

   NOTICE:

   
   
   1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      
   2. Do not use any tools to separate the pipe and connector.
      
   3. Do not forcefully bend or twist the nylon tube.
      
   4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      
   5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      
   6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
      

   Text in Illustration

   *1	Retainer
   *2	Nylon Tube
   *3	Pipe
   *4	O-Ring
   *5	Fuel Tube Connector

4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.
   

5. To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.
   

Observe these precautions when connecting the fuel tube connector (for quick type A).

1. Check that there is no damage or contamination in the connected part of the pipe.
   





2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.
   

   Text in Illustration

   Push





3. After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.
   

   Text in Illustration

   Pull

4. Fuel Hose Connector Cover Type:
   Attach the lock claws to the connector by pushing down on the cover.
   

5. Check for any fuel leaks.
   

Observe these precautions when disconnecting the fuel tube connector (for quick type B):

1. Check if there is any dirt or mud on the pipe and around the connector before disconnecting them. Clean if necessary.
   

2. Disconnect the parts by hand.
   





3. If the connector and pipe are stuck, push and pull the connector to disconnect the pipe and pull it out.
   

   Text in Illustration

   	Turn
   	Pull

   NOTICE:

   
   
   1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      
   2. Do not use any tools to separate the pipe and connector.
      
   3. Do not forcefully bend or twist the nylon tube.
      
   4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      
   5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      
   6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
      

   Text in Illustration

   *1	Nylon Tube
   *2	O-Ring
   *3	Retainer
   *4	Pipe

4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.
   

5. To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.
   

Observe these precautions when connecting the fuel tube connector (for quick type B):

1. Align the axis of the connector with the axis of the pipe and push in the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of new engine oil to the tip of the pipe.
   

   Text in Illustration

   Push





2. After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.
   

   Text in Illustration

   Pull

3. Check for fuel leaks.
   

Observe these precautions when disconnecting the fuel tube connector (for quick type C).

1. Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.
   





2. Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.
   

   Text in Illustration

   *1	Retainer
   	Push
   	Down
   	Pull

   HINT:

   If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

   Text in Illustration

   	Pull
   	Push

   NOTICE:

   
   
   1. Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      
   2. Do not use any tools to separate the pipe and connector.
      
   3. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
      
   4. Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.
      
   5. Do not forcibly bend, twist or turn the nylon tube.
      
   6. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.
      
   7. If the pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the main tube.
      

   Text in Illustration

   *1	Pipe
   *2	Retainer
   *3	Nylon Tube
   *4	Connector
   *5	O-Ring

3. Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.
   

4. To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.
   

Observe these precautions when connecting the fuel tube connector (for quick type C).

1. Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.
   





2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and then push up on the retainer.
   

   Text in Illustration

   *1	Retainer
   	Up
   	Push

   NOTICE:

   1. Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
      
   2. After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.
      

   Text in Illustration

   Pull

Observe these precautions when handling the nylon tube.

NOTICE:

1. Be careful not to turn the connection part of the nylon tube and the quick connector when connecting them.
   
2. Do not kink the nylon tube.
   
3. Do not remove the EPDM protector on the outside of the nylon tube.
   
4. Do not bend the nylon tube as this may cause blockage.
   

Observe these precautions when disconnecting the fuel tank breather tube connector:

1. Pinch the retainer and pull out the fuel tank breather tube connector with the fuel tank breather tube connector pushed toward the pipe to disconnect the fuel tank breather tube from the pipe.
   

   Text in Illustration

   *1	Fuel Tank Breather Tube Connector
   *2	Pipe
   	Push
   	Pinch

   NOTICE:

   1. Remove dirt or foreign objects on the fuel tank breather tube connector before performing this procedure.
      
   2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank breather tube connector has the O-ring that seals the pipe.
      
   3. Perform this work by hand. Do not use any tools.
      
   4. Do not forcibly bend, kink or twist the nylon tube.
      
   5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank breather tube.
      
   6. If the fuel tank breather tube connector and pipe are stuck, push and pull them to release them.
      

   Text in Illustration

   *1	Fuel Tank Breather Tube Connector
   *2	Pipe
   *3	Nylon Tube
   *4	O-Ring

Observe these precautions when connecting the fuel tank breather tube connector:

1. Align the fuel tank breather tube connector with the pipe, and then push in the fuel tank breather tube connector until the retainer makes a "click" sound to connect the fuel tank breather tube to the pipe.
   

   Text in Illustration

   Push

   NOTICE:

   1. Check that there are no scratches or foreign objects on the connected part of the fuel tank breather tube connector and pipe before performing this procedure.
      
   2. After connecting the fuel tank breather tube, check that the fuel tank breather tube is securely connected by pulling the fuel tank breather tube connector.
      




2. After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.
   

   Text in Illustration

   Pull

3. Inspect for fuel leaks.
   

Inspect for fuel leaks (LandCruiser RM000000Q460CAX_02_0091.html).