Back Door Lock Installation


  1. INSTALL BACK DOOR LOCK ASSEMBLY

  2. INSTALL BACK DOOR SERVICE HOLE COVER

  3. INSTALL DOOR INSIDE HANDLE SUB-ASSEMBLY (w/ Back Door Tire Carrier, for Face to Face Seat Type)

  4. INSTALL BACK DOOR TRIM PANEL ASSEMBLY

  5. INSTALL BACK DOOR INSIDE HANDLE BEZEL (w/ Back Door Tire Carrier, for Face to Face Seat Type)

  6. INSTALL BACK DOOR LOCK COVER (w/o Back Door Tire Carrier, for Standard Type)

  7. INSTALL TOOL CASE

  8. INSTALL UPPER TOOL BOX PANEL SUB-ASSEMBLY

  9. INSTALL BACK DOOR TRIM COVER

  10. INSTALL BACK DOOR SIDE GARNISH LH

  11. INSTALL BACK DOOR SIDE GARNISH RH

  12. INSTALL CENTER BACK DOOR GARNISH

Back Door Lock -- Installation



1. INSTALL BACK DOOR LOCK ASSEMBLY
NOTICE:
  1. When reusing the removed back door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water into the connection. This may result in a malfunction of the front door lock assembly.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Connect the cable.

  1. Install a new door lock wiring harness seal to the front door lock assembly.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Door Lock.Power Door Lock Control System.Back Door Lock Installation

  1. Using a T30 "TORX" wrench, install the back door lock assembly with the 3 screws.

    Text in Illustration
    *A
    		for Standard Type
    *B
    		w/ Back Door Tire Carrier, for Face to Face Seat Type
    Torque:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}

  1. Connect the connector.



2. INSTALL BACK DOOR SERVICE HOLE COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Door Lock.Power Door Lock Control System.Back Door Lock Installation

  1. Apply new butyl tape to the back door panel.

  1. Attach the rear door service hole cover using to the reference points on the rear door panel.

    Text in Illustration
    *1
    		Reference Point
    NOTICE:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the seal quality.


3. INSTALL DOOR INSIDE HANDLE SUB-ASSEMBLY (w/ Back Door Tire Carrier, for Face to Face Seat Type)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Connect the 2 cables to the inside handle sub-assembly.

  1. Attach the claws and guide to install the inside handle sub-assembly.



4. INSTALL BACK DOOR TRIM PANEL ASSEMBLY

  1. w/o Back Door Tire Carrier:

    1. Attach the 15 clips to install the back door trim panel assembly.

    2. Install the bolt.

  1. w/ Back Door Tire Carrier:

    1. Attach the 16 clips to install the back door trim panel assembly.

    2. Install the bolt.

  1. for Face to Face Seat Type:

    1. Attach the 15 clips to install the back door trim panel assembly.

    2. Install the bolt.

  1. Install the screw.

  1. Attach the claw to install the cover.



5. INSTALL BACK DOOR INSIDE HANDLE BEZEL (w/ Back Door Tire Carrier, for Face to Face Seat Type)

  1. Attach the 5 claws to install the back door inside handle bezel.

  1. Install the screw.



6. INSTALL BACK DOOR LOCK COVER (w/o Back Door Tire Carrier, for Standard Type)

  1. Attach the 6 claws to install the back door lock cover.



7. INSTALL TOOL CASE

  1. Attach the 2 claws to install the tool case.



8. INSTALL UPPER TOOL BOX PANEL SUB-ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 3 claws.

  1. Install the upper tool box panel sub-assembly as shown in the illustration.



9. INSTALL BACK DOOR TRIM COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 4 claws.

  1. Install the back door trim cover as shown in the illustration.



10. INSTALL BACK DOOR SIDE GARNISH LH

  1. Attach the 2 clips and claw to install the back door side garnish.



11. INSTALL BACK DOOR SIDE GARNISH RH

  1. Attach the 2 clips and claw to install the back door side garnish.



12. INSTALL CENTER BACK DOOR GARNISH

  1. Attach the 4 clips to install the back door center garnish.