INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)
INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)
INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)
INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)
Rear Door Lock -- Inspection |
1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System) |

*a | Lock | *b | Unlock |
*c | Component without harness connected (Rear Door Lock assembly LH) | - | - |
Check the door lock motor operation.
Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)Lock Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)Unlock
- If the result is not as specified, replace the rear door lock assembly.
Check the detection switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (LSSR) - 9 (E) Unlock Below 1 Ω 6 (LSSR) - 9 (E) Lock 10 kΩ or higher
- If the result is not as specified, replace the rear door lock assembly.
2. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System) |

*a | Lock | *b | Unlock |
*c | Component without harness connected (Rear Door Lock Assembly LH) | - | - |
Check the door lock motor operation.
Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)Lock Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)Unlock Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)Set Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)Unset
- If the result is not as specified, replace the rear door lock assembly.
Check the detection switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 5 (LSSR) - 6 (E) Unlock Below 1 Ω 5 (LSSR) - 6 (E) Lock 10 kΩ or higher
- If the result is not as specified, replace the rear door lock assembly.
3. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System) |

*a | Unlock | *b | Lock |
*c | Component without harness connected (Rear Door Lock Assembly RH) | - | - |
Check the door lock motor operation.
Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)Lock Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)Unlock
- If the result is not as specified, replace the rear door lock assembly.
Check the detection switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (LSSR) - 9 (E) Unlock Below 1 Ω 6 (LSSR) - 9 (E) Lock 10 kΩ or higher
- If the result is not as specified, replace the rear door lock assembly.
4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System) |

*a | Unlock | *b | Lock |
*c | Component without harness connected (Rear Door Lock Assembly RH) | - | - |
Check the door lock motor operation.
Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)Lock Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)Unlock Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)Set Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)Unset
- If the result is not as specified, replace the rear door lock assembly.
Check the detection switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 9 (LSSR) - 10 (E) Unlock Below 1 Ω 9 (LSSR) - 10 (E) Lock 10 kΩ or higher
- If the result is not as specified, replace the rear door lock assembly.