Front Wiper Motor Installation

Attach the claw to install the wiper motor wire.

Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Connect the connector.

w/o Spring:

1. Apply MP grease to the crank arm pivot of the front wiper crank.
   

   Text in Illustration

   *1	Crank Arm Pivot
   	MP grease





2. Connect the rod to the crank arm pivot of the front wiper crank.
   

Check the automatic stop position.

1. Check that the motor stops automatically at the automatic stop position (LandCruiser RM000002XJR02MX_01_0002.html).
   

Install the front wiper crank sub-assembly to the front wiper motor assembly with the nut so that center lines of the crank arm spring and wiper link stay are parallel.

Torque:

17 N*m{173 kgf*cm, 13 ft.*lbf}

HINT:

Hold the front wiper crank sub-assembly by hand when tightening the nut.

Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

Text in Illustration

*1	Crank Arm Pivot
	MP grease

Connect the rod of the windshield wiper link to the front wiper crank.

Attach the grommet as shown in the illustration.

Torque:

7.0 N*m{71 kgf*cm, 62 in.*lbf}

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

Install the windshield wiper motor and link with the 2 bolts.

Connect the connector.

Attach the clamp.

Attach the 10 guides (B).

Attach the 6 claws and guide (A) as shown in the illustration.

Install the 2 clips to the cowl top ventilator louver sub-assembly.

Attach the 2 claws and 3 guides to install the center No. 2 cowl top ventilator louver.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.

When reusing the front wiper arm and blade assembly RH:

1. Clean the wiper arm serrations.
   

   Text in Illustration

   *1	Wiper Arm Serration
   *2	Wire Brush
   *3	Wiper Pivot Serration

When reusing the windshield wiper link assembly:

1. Clean the wiper pivot serrations with a wire brush.
   

Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:

25 N*m{255 kgf*cm, 18 ft.*lbf}

HINT:

1. Hold the wiper arm by hand while tightening the nut.
   
2. Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.
   

When reusing the front wiper arm and blade assembly LH:

1. Clean the wiper arm serrations.
   

   Text in Illustration

   *1	Wiper Arm Serration
   *2	Wire Brush
   *3	Wiper Pivot Serration

When reusing the windshield wiper link assembly:

1. Clean the wiper pivot serrations with a wire brush.
   

Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:

25 N*m{255 kgf*cm, 18 ft.*lbf}

HINT:

1. Hold the wiper arm by hand while tightening the nut.
   
2. Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.
   

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

Attach the 3 claws to install the wiper arm cover.

HINT:

Use the same procedure described for the LH side.

Attach the 5 claws to install the front fender to cowl side seal LH.

Attach the 4 clips and 2 guides to install the fender side panel.

Install the upper radiator support seal with the 13 clips.