Dtc P2080 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2080, P2084 OR P242B)

READ VALUE USING GTS (EXHAUST TEMPERATURE)

INSPECT EXHAUST GAS TEMPERATURE SENSOR

REPLACE EXHAUST GAS TEMPERATURE SENSOR

REPLACE ECM

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P2080 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1

DTC P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2

DTC P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3


DESCRIPTION

Refer to DTC P0545 (LandCruiser RM00000188D0AOX_01.html).

P2080
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Check the exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*
*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
The change in the exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
  1. Exhaust gas temperature sensor
  2. ECM (soak timer)

P2084
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Check the No. 2 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*
*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
The change in the No. 2 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
  1. No. 2 Exhaust gas temperature sensor
  2. ECM (soak timer)

P242B
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Check the No. 3 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*
*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
The change in the No. 3 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
  1. No. 3 Exhaust gas temperature sensor
  2. ECM (soak timer)

Related Data List
DTC No.
Data List
P2080
P2084
P242B
  1. Exhaust Temperature B1S1
  2. Exhaust Temperature B1S2
  3. Exhaust Temperature B1S3
HINT:
  1. Sensor 1 represents the sensor located upstream of the DOC catalytic converter.
  2. Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
  3. Sensor 3 represents the sensor located downstream of the DPF catalytic converter.
  4. If DTC P2080, P2084 or P242B is stored, the following symptoms may appear:
    1. White smoke

WIRING DIAGRAM

Refer to DTC P0545 (LandCruiser RM00000188D0AOX_03.html).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (LandCruiser RM0000012XK0AVX.html) and initialization (LandCruiser RM000000TIN08IX.html).
HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2080, P2084 OR P242B)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result
    Result
    		Proceed to
    DTC P2080, P2084 or P242B is output
    		A
    DTC P2080, P2084 or P242B and other DTCs are output
    		B



B
GO TO DTC CHART (LandCruiser RM0000031HW07PX.html)
A


2.READ VALUE USING GTS (EXHAUST TEMPERATURE)

  1. Leave the vehicle as is for 1 to 2 hours with the engine stopped.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

  1. Record the exhaust temperature displayed on the GTS.


NEXT


3.INSPECT EXHAUST GAS TEMPERATURE SENSOR

  1. Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

  1. Stop the vehicle.

  1. Connect the GTS to the DLC3.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

  1. Read the value.

    Result:

    Result
    		Proceed to
    Difference between Exhaust Temperature B1S1 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S1 checked after driving is within +/-15°C (27°F)
    		A
    Difference between Exhaust Temperature B1S2 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S2 checked after driving is within +/-15°C (27°F)
    Difference between Exhaust Temperature B1S3 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S3 checked after driving is within +/-15°C (27°F)
    Difference between exhaust temperature recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and exhaust temperature checked after driving is equal to or greater than +/- 15°C (27°F)
    		B


B
Go to step 5
A


4.REPLACE EXHAUST GAS TEMPERATURE SENSOR
HINT:
Replace the exhaust temperature sensor that changed a small amount in "INSPECT EXHAUST GAS TEMPERATURE SENSOR".

  1. Replace the exhaust gas temperature sensor (LandCruiser RM000005UK3000X.html).

  1. Replace the No. 2 exhaust gas temperature sensor (LandCruiser RM000005UK3000X.html).

  1. Replace the No. 3 exhaust gas temperature sensor (LandCruiser RM000005UK3000X.html).



NEXT
Go to step 6

5.REPLACE ECM

  1. Replace the ECM (LandCruiser RM0000013Z002DX.html).


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Leave the vehicle as is for 1 to 2 hours with the engine stopped.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

  1. Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

  1. Stop the vehicle.

  1. Connect the GTS to the DLC3.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

  1. Check the exhaust temperature after leaving the vehicle for 1 to 2 hours and after driving.

    Standard:
    +/-15°C(27°F) or more

NEXT

END