Power Window Regulator Motor (For Rear Door) Removal


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  3. REMOVE ASSIST GRIP COVER LH

  4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  6. REMOVE REAR SPEAKER SET

  7. REMOVE REAR DOOR SERVICE HOLE COVER

  8. REMOVE REAR DOOR GLASS RUN LH

  9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  12. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

  13. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Power Window Regulator Motor (For Rear Door) -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.



3. REMOVE ASSIST GRIP COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using moulding remover A, detach the 8 claws and remove the assist grip cover.



4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 3 screws.

  1. Using a clip remover, detach the 9 clips.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Window Glass.Power Window Control System.Power Window Regulator Motor (For Rear Door) Removal

  1. Disconnect each connector.

    Text in Illustration
    *A
    		for 14 Speakers
    *B
    		for 9 Speakers


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a screwdriver, detach the claw and remove the clamp.



5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.



6. REMOVE REAR SPEAKER SET


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the connector.

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the rear speaker set.

    NOTICE:
    Do not touch the cone of the speaker.


7. REMOVE REAR DOOR SERVICE HOLE COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the connector.

  1. Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


8. REMOVE REAR DOOR GLASS RUN LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door glass run.



9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Window Glass.Power Window Control System.Power Window Regulator Motor (For Rear Door) Removal

  1. Loosen the temporary bolt.

    Text in Illustration
    *1
    		Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window division bar sub-assembly.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.



10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.



11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Window Glass.Power Window Control System.Power Window Regulator Motor (For Rear Door) Removal

  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


12. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Window Glass.Power Window Control System.Power Window Regulator Motor (For Rear Door) Removal

  1. Loosen the temporary bolt.

    Text in Illustration
    *1
    		Temporary Bolt
    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.



13. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.