Entry And Start System (For Start Function) How To Proceed With Troubleshooting

  1. VEHICLE BROUGHT TO WORKSHOP

  2. CUSTOMER PROBLEM ANALYSIS CHECK

  3. INSPECT BATTERY VOLTAGE

  4. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

  5. CHECK FOR DTC*

  6. INSPECT BASIC OPERATION

  7. PROBLEM SYMPTOMS TABLE

  8. OVERALL ANALYSIS AND TROUBLESHOOTING*

  9. REPAIR OR REPLACE

  10. CONFIRMATION TEST

Entry And Start System (For Start Function) -- How To Proceed With Troubleshooting


HINT:
  1. Use these procedures to troubleshoot the push-button start function.
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS CHECK
      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      1. The following 5 items are important points in the problem analysis:

        What
        		Vehicle model, system name
        When
        		Date, time, occurrence frequency
        Where
        		Road conditions
        Under what conditions?
        		Running conditions, driving conditions, weather conditions
        How did it happen?
        		Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE
      Standard voltage:
      11 to 14 V
      If the voltage is below 11 V, recharge or replace the battery before proceeding.

    NEXT


    4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result
      		Proceed to
      CAN DTC is not output
      		A
      CAN DTC is output
      		for LHD with Entry and Start System
      		B
      for RHD with Entry and Start System
      		C



    		B.
    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (LandCruiser RM000001RSO0C5X.html)

    		C.
    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (LandCruiser RM000001RSO0BZX.html)
    A


    5.CHECK FOR DTC*

    1. Check for DTCs and note any codes that are output (LandCruiser RM000000YEH0GKX.html).

    2. Clear the DTCs (LandCruiser RM000000YEH0GKX.html).

    3. Recheck for DTCs.

      Result
      Result
      		Proceed to
      DTC is not output again
      		A
      DTC is output again
      		B



    		B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (LandCruiser RM000000XIZ0K8X.html)
    A


    6.INSPECT BASIC OPERATION
      1. *1: for Automatic Transaxle
      2. *2: for Manual Transaxle

    1. Check that the engine can be started by the basic operation.

      1. Push the engine switch when the brake pedal*1 or clutch pedal*2 is depressed and the shift lever is in P*1. Check that the engine starts.

        OK:
        Engine starts.

    2. Check that the engine switch mode can be changed by pushing the engine switch.

      1. Without depressing the brake pedal*1 or clutch pedal*2, push the engine switch repeatedly. Check that the power source mode turns from off to on (ACC) to on (IG) and back to off.

        OK:
        Power source mode changes as described above.

      2. With the brake pedal*1 or clutch pedal*2 depressed and the shift lever in P*1, push the engine switch. Check that the engine starts normally from any power source mode status.

        OK:
        Engine starts normally from any power source mode status.

    NEXT


    7.PROBLEM SYMPTOMS TABLE

    1. Refer to the Problem Symptoms Table (LandCruiser RM000000XI60N9X.html).

      Result
      Result
      		Proceed to
      Fault is not listed in the problem symptoms table
      		A
      Fault is listed in the problem symptoms table
      		B



    		B.
    Go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*

    1. Terminals of ECU (LandCruiser RM000000XI20FKX.html).

    2. Data List/Active Test (LandCruiser RM000000XI50GFX.html).


    NEXT


    9.REPAIR OR REPLACE

      NEXT


      10.CONFIRMATION TEST

        NEXT

        END