Dtc C1432 Steering Angle Sensor Power Source Voltage Malfunction


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK TERMINAL VOLTAGE (IG, BAT)

CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

DTC C1432 Steering Angle Sensor Power Source Voltage Malfunction


DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code
DTC Detection Condition
Trouble Area
C1432
A steering angle sensor power supply malfunction signal is received from the steering angle sensor.
  1. ECU-B fuse
  2. ECU-IG NO. 1 fuse
  3. Steering angle sensor power supply
  4. Steering angle sensor (Spiral cable sub-assembly)

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1432 Steering Angle Sensor Power Source Voltage Malfunction


INSPECTION PROCEDURE

NOTICE:
  1. Do not remove the steering angle sensor from the spiral cable sub-assembly.
  2. When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
  1. When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (LandCruiser RM000000YUO0SYX.html).
  2. When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.
1.CHECK TERMINAL VOLTAGE (IG, BAT)

  1. Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the G33 steering angle sensor connector.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1432 Steering Angle Sensor Power Source Voltage Malfunction

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    G33-5 (IG) - Body ground
    		Ignition switch ON
    		11 to 14 V
    G33-6 (BAT) - Body ground
    		Always
    		11 to 14 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Steering Angle Sensor)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

  1. Turn the ignition switch off.

  1. Disconnect the G33 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G33-2 (ESS) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (LandCruiser RM000000SS909QX.html)