Airbag System Diagnosis System

Vibration method: When vibration seems to be the major cause.

HINT:

Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).

1. Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.
   

   NOTICE:

   Shaking the relays too strongly may result in open relays.

2. Slightly shake the connector vertically and horizontally.
   

3. Slightly shake the wire harness vertically and horizontally.
   

   HINT:

   The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.

Primary check.

1. Turn the ignition switch off. Wait for at least 2 seconds and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.
   

   HINT:

   If trouble is detected during the primary check, the SRS warning light remains on even after the primary check period (of approximately 6 seconds) has elapsed.

Constant check.

1. After the primary check, the center airbag sensor constantly monitors the airbag system for trouble.
   

   HINT:

   If trouble is detected during the constant check, the center airbag sensor functions as follows:

   1. The SRS warning light comes on.
      
   2. The SRS warning light goes off, and then comes on. This blinking pattern indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.
      

Review.

1. When the airbag system is normal:
   The SRS warning light comes on only during the primary check period (for approximately 6 seconds after the ignition switch is turned ON).
   

2. When the airbag system has trouble:
   

   1. The SRS warning light remains on even after the primary check period has elapsed.
      
   2. The SRS warning light goes off after the primary check, but comes on again during the constant check.
      
   3. The SRS warning light does not come on when turning the ignition switch from off to ON.
      

   HINT:

   The center airbag sensor functions to keep the SRS warning light on if the airbag has been deployed.

Turn the ignition switch to ON and check that the SRS warning light comes on for approximately 6 seconds (primary check).

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned ON (constant check).

HINT:

When any of the following symptoms occur, refer to the "Problem Symptoms Table" (LandCruiser RM0000038YS03DX.html).

1. The SRS warning light comes on occasionally, after the primary check period has elapsed.
   
2. The SRS warning light comes on, but a DTC is not output.
   
3. The ignition switch is turned from off to ON, but the SRS warning light does not come on.
   

Initial check

1. Turn the ignition switch to ON.
   

2. The airbag cutoff indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.
   





3. Approximately 6 seconds after the ignition switch is turned to ON, the airbag cutoff indicator will be airbag cutoff indicator depending on the conditions listed below.
   
   

   Airbag Cutoff Switch	Airbag Cutoff Indicator
   ON	Off
   OFF	On
   Switch failure	On

   HINT:

   The airbag cutoff indicator is based on the timing chart below in order to check the indicator light circuit.

   
   
   
   

Turn the ignition switch to ON.

Check that the airbag cutoff indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

HINT:

Refer to the table in the previous step regarding the airbag cutoff indicator when the ignition switch is turned ON and approximately 6 seconds have passed.

FUNCTION OF ACTIVATION PREVENTION MECHANISM

1. An activation prevention mechanism is built into the connector (on the center airbag sensor side) of the airbag system squib circuit to prevent accidental airbag activation.
   

2. This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and cutting off external electricity to prevent accidental airbag activation.
   

RELEASING OF ACTIVATION PREVENTION MECHANISM

1. To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.020 in.)) between the terminals and the short spring to break the connection.
   





2. Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.
   

   CAUTION:

   Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.

   NOTICE:

   1. Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.
      
   2. To prevent the terminal and the short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.