Dtc C1232 Acceleration Sensor Stuck Malfunction


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FOR DTC

CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)

DTC C1232 Acceleration Sensor Stuck Malfunction

DTC C1243 Acceleration Sensor Stuck Malfunction

DTC C1245 Acceleration Sensor Output Malfunction

DTC C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

DTC Code
DTC Detection Condition
Trouble Area
C1232
At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or GL2 is below 80 mV and the fluctuation range of the signal of the other is higher than 1.9 V for 30 seconds or more.
  1. ECU-IG NO. 1 fuse
  2. Sensor installation
  3. Harness or connector
  4. Yaw rate and acceleration sensor
  5. CAN communication system
C1243
The following condition repeats 16 times.
  1. GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
C1245
The following condition continues for at least 60 seconds.
  1. The difference between the values calculated from the acceleration sensor value and vehicle speed exceeds 0.35 G.
C1279
Stored during test mode.

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1232 Acceleration Sensor Stuck Malfunction


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the yaw rate and acceleration sensor, perform calibration (LandCruiser RM00000452J00ZX.html).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1.CHECK FOR DTC

  1. Clear the DTCs (LandCruiser RM0000046KV016X.html).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check if DTCs U0073, U0123, C1210 and/or C1336 are output (LandCruiser RM0000046KV016X.html).

    Result
    Result
    		Proceed to
    DTC U0073, U0123, C1210 and/or C1336 are not output
    		A
    DTC U0073 and/or U0123 are output (for LHD)
    		B
    DTC U0073 and/or U0123 are output (for RHD)
    		C
    DTC C1210 and/or C1336 are output
    		D


B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (LandCruiser RM000001RSO0C5X.html)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (LandCruiser RM000001RSO0BZX.html)

D
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (LandCruiser RM0000045Z601DX.html)
A


2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

  1. Check that the yaw rate and acceleration sensor is installed properly.

    OK:
    The sensor is tightened to the specified torque. The sensor is not tilted.


NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (LandCruiser RM000000SS207WX.html)
OK


3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)

  1. Disconnect the G52 yaw rate and acceleration sensor connector.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1232 Acceleration Sensor Stuck Malfunction

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G52-4 (IG) - Body ground
    		Ignition switch ON
    		11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G52-1 (GND) - Body ground
    		Always
    		Below 1 Ω
Text in Illustration
*a
Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)

Result
Result
Proceed to
OK (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
A
OK (When troubleshooting in accordance with Problem Symptoms Table)
B
NG
C


B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (LandCruiser RM000000OS705AX.html)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE YAW RATE AND ACCELERATION SENSOR (LandCruiser RM000000SS507KX.html)