Dtc P245C Egr Cooler Bypass Control Circuit Low

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
2Kd-Ftv Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)

CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

REPLACE ECM

REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)

REPAIR OR REPLACE HARNESS OR CONNECTOR

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P245C EGR Cooler Bypass Control Circuit Low

DTC P245D EGR Cooler Bypass Control Circuit High


DESCRIPTION

The vacuum switching valve (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

P245C
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch to ON for 3 seconds
Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
  1. Open or short in vacuum switching valve (for EGR bypass valve) circuit
  2. Vacuum switching valve (for EGR bypass valve)
  3. ECM

P245D
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch to ON for 3 seconds
Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
  1. Open or short in vacuum switching valve (for EGR bypass valve) circuit
  2. Vacuum switching valve (for EGR bypass valve)
  3. ECM

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P245C Egr Cooler Bypass Control Circuit Low


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK071X.html) and initialization (HILUX_TGN26 RM000000TIN04FX.html).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
1.INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)

  1. Inspect the vacuum switching valve (for EGR bypass valve) (HILUX_TGN26 RM0000046SD00JX.html).



NG
Go to step 5
OK


2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P245C Egr Cooler Bypass Control Circuit Low

  1. Disconnect the vacuum switching valve (for EGR bypass valve) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    C100-1 - Body ground
    		Ignition switch to ON
    		11 to 14 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Vacuum Switching Valve (for EGR Bypass Valve))

  1. Reconnect the vacuum switching valve (for EGR bypass valve) connector.



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

  1. Disconnect the vacuum switching valve (for EGR bypass valve) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    		Condition
    		Specified Condition
    C100-2 - C23-19 (ECBV)
    		Always
    		Below 1 Ω
    Standard Resistance (Check for Short):
    Tester Connection
    		Condition
    		Specified Condition
    C100-2 or C23-19 (ECBV) - Body ground
    		Always
    		10 kΩ or higher

  1. Reconnect the vacuum switching valve (for EGR bypass valve) connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4.REPLACE ECM

  1. Replace the ECM (HILUX_TGN26 RM0000013Z001HX.html).



NEXT
Go to step 7

5.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)

  1. Replace the vacuum switching valve (for EGR bypass valve).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. Repair or replace the harness or connector.

    HINT:
    If the voltage at the vacuum switching valve (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve (for EGR bypass valve) and EFI relay (including the EFI No. 2 fuse).

NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (HILUX_TGN26 RM000000PDK120X.html).

  1. Turn the ignition switch to ON for 3 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END