Dtc C1282 Center Differential Lock Position Switch

Brake. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
Brake Control Dynamic Control Systems. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK TERMINAL VOLTAGE (EXI TERMINAL)

CHECK TEST MODE DTC

CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH)

DTC C1282 Center Differential Lock Position Switch


DESCRIPTION

DTC C1282 is stored only in Test Mode.

DTC Code
DTC Detection Condition
Trouble area
C1282
Stored during Test Mode.
  1. Harness or connector
  2. Transfer system
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1282 Center Differential Lock Position Switch


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (HILUX_TGN26 RM000000XHR073X.html).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
1.CHECK TERMINAL VOLTAGE (EXI TERMINAL)

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the 4WD state using the transfer shift lever.



    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1282 Center Differential Lock Position Switch

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    A36-20 (EXI) - Body ground
    1. Ignition switch ON
    2. Transfer shift position H4
    		Below 1.5 V

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the 2WD state using the transfer shift lever.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    A36-20 (EXI) - Body ground
    1. Ignition switch ON
    2. Transfer shift position H2
    		11 to 14 V
Text in Illustration
*a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


NG
Go to step 3
OK


2.CHECK TEST MODE DTC

  1. Switch the vehicle to Test Mode, check the H2 to H4 shift operation, and then check that DTC C1282 is cleared (HILUX_TGN26 RM000000XHT091X.html).

    Result
    Result
    		Proceed to
    Test Mode DTC is not cleared
    		A
    Test Mode DTC is cleared
    		B


B
USE SIMULATION METHOD TO CHECK (HILUX_TGN26 RM000004QR7008X.html)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (HILUX_TGN26 RM0000010K001MX.html)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH)

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the 4WD detection switch (differential vacuum actuator assembly) connector.

  1. Disconnect the 4 wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    A36-20 (EXI) - C31-3 (ADD)
    		Always
    		Below 1 Ω
    A36-20 (EXI) - C37-8 (ADD)
    		Always
    		Below 1 Ω
    A36-20 (EXI) - Body ground
    		Always
    		10 kΩ or higher
    C31-4 (GND) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (HILUX_TGN26 RM0000011JJ026X.html)