Window Glass. Power Window Regulator Motor (For Rear Door) Removal

Vehicle Exterior. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

Window Glass. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

PRECAUTION
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL LH
REMOVE DOOR PULL HANDLE
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
REMOVE REAR DOOR NO. 2 TRIM BRACKET
REMOVE REAR DOOR SERVICE HOLE COVER LH
REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
REMOVE REAR DOOR GLASS RUN LH
REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Power Window Regulator Motor (For Rear Door) -- Removal

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (HILUX_TGN26 RM000004QR1006X.html).

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3008X.html).

3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL LH

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

Using a moulding remover, detach the 2 clips and 2 claws.

Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

4. REMOVE DOOR PULL HANDLE

Remove the screw and door pull handle.

5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Remove the clip and screw.

Detach the 9 clips and remove the rear door trim board.

6. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Window Glass.Power Window Control System (W/ Jam Protection Function).Power Window Regulator Motor (For Rear Door) Removal

Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.

Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.

7. REMOVE REAR DOOR NO. 2 TRIM BRACKET

Remove the 2 screws and rear door No. 2 trim bracket.

8. REMOVE REAR DOOR SERVICE HOLE COVER LH

w/ Rear Speaker:
Pull out the rear door inside locking cable, rear door lock remote control cable and wire harness from the rear door service hole cover, and then remove the rear door service hole cover.
HINT:
Remove any remaining butyl tape from the rear door panel.

w/o Rear Speaker:
Pull out the rear door inside locking cable and rear door lock remote control cable from the rear door service hole cover, and then remove the rear door service hole cover.
HINT:
Remove any remaining butyl tape from the rear door panel.

9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Partially remove the rear door glass run as shown in the illustration.

Remove the 2 bolts.

Remove the rear door window division bar together with the rear door glass run as shown in the illustration.

Remove the rear door window division bar from the rear door glass run.

10. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

w/ Power Window:
1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
2. Connect the cable to the negative (-) battery terminal.
3. Move the rear door glass so that the rear door glass channel can be seen.
4. Disconnect the cable from the negative (-) battery terminal.
  NOTICE:
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3008X.html).
5. Remove the rear power window regulator switch assembly with rear door armrest base panel.

w/o Power Window:
1. Temporarily install the rear door window regulator handle.
2. Move the rear door glass so that the rear door glass channel can be seen.
3. Remove the rear door window regulator handle.

Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.

Remove the rear door glass by passing it through the cutout of the rear door panel in the direction indicated by the arrow in the illustration.
NOTICE:
Do not damage the door glass.
Text in Illustration
*a
Rear Door Panel Cutout

Text in Illustration
*a	Rear Door Panel Cutout

11. REMOVE REAR DOOR GLASS RUN LH

Remove the front side of the rear door glass run.

12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

w/ Power Window:
1. Disconnect the connector.
2. Loosen the temporary bolt.
  NOTICE:
  Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.
  Text in Illustration
  *1
  Temporary Bolt
3. Remove the 3 bolts and rear door window regulator.
4. Remove the temporary bolt from the rear door window regulator.

Text in Illustration
*1	Temporary Bolt

w/o Power Window:
1. Loosen the temporary bolt.
  NOTICE:
  Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.
  Text in Illustration
  *1
  Temporary Bolt
2. Remove the 2 bolts and rear door window regulator.
3. Remove the temporary bolt from the rear door window regulator.

Text in Illustration
*1	Temporary Bolt

13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly LH.